Disassembly and Assembly

FRONT SEAT


Disassembly and Assembly


SEATBACK

Disassembly
1. Remove the seatback board.





- Remove the seatback board band from seat cushion bottom side.
- Remove the seatback board mounting screws (A).





- Pull down the seatback board to release the pawls.

Broken Triangle : Pawl

2. Disconnect the harness connectors and remove the harness clamps.





- Remove the seatback trim retainer (1).





- Disconnect the seatback heater harness connector (A)
(Heater seat only), lumbar support harness connector (B)
(Driver's seat only) and reclining motor harness connector (C)
(Power seat only).
3. Remove the side air bag module.





- Remove the seatback trim retainer.
- Remove the side air bag module cover mounting screws (A).
- Remove the side air bag module.
4. Remove the lumbar support lever knob. (Manual lumbar support seat only.)





Pull snap ring (1) upward, and remove lumbar support lever knob (2) from seatback frame with hook and pick tool.
5. Remove the seatback trim and seatback pad.





- Remove the headrest holder.

CAUTION:
Before installing headrest holder check its orientation.
(front/rear and right/left)
- Remove the seatback trim and seatback pad from the seatback frame.
- Remove the hog rings, and separate the seatback trim and seatback pad.
6. Remove the seatback silencer.
7. Remove the seatback frame.





Remove the seatback frame mounting bolts (A).

Assembly
Assemble in the reverse order of disassembly.

CAUTION:
Install the hog rings of seatback trim in position, and then securely connect the trim or trim cord with the pad side wire.

SEAT CUSHION

Disassembly

CAUTION:
Never disassemble front passenger seat cushion assembly.
Always replace as an assembly.
For front passenger seat service parts, refer to the service part catalogue.
1. Remove the seatback board.





- Remove the seatback board fixing band on the bottom of seat cushion.
- Remove the seatback board mounting screws (A).





- Pull down the seatback board to release the pawls.

Broken Triangle : Pawl

2. Disconnect the harness connectors and remove the harness clamps.





- Remove the seatback trim retainer (1).





- Remove the seatback heater harness connector (A), lumbar support harness connector (B) (Driver's power seat only) and reclining motor harness connector (C).





- Remove the side air bag module harness (A) and disconnect the seat cushion heater harness connector (B).
3. Remove the seatback assembly.





- Remove the seatback mounting bolts (A), and then remove the seatback assembly.
4. Remove the seat cushion front finisher. (Power seat only)





- Remove the seat cushion front finisher mounting screws (A).
- Remove the seat cushion front finisher mounting pawl.

Broken Triangle : Pawl

5. Remove the seat cushion outer finisher outside.
a. Power seat
- Remove the seat control switch knob and reclining switch knob and lumbar support switch.





- Remove the seat cushion outer finisher mounting screw (A), metal clips and pawls.

Broken Square : Metal clip
Broken Triangle : Pawl

- Disconnect the seat control switch, reclining switch and lumbar support switch harness connectors (Driver's seat only).
b. Manual seat





- Remove the pawls, and then lifter lever knob finisher (1).
(Driver's manual seat only)

Broken Triangle : Pawl

- Remove the mounting screws, and remove the lifter lever (2).
(Driver's manual seat only)





- Pull out the reclining lever while holding and raising the pawl.

Broken Triangle : Pawl






- Remove the mounting screws (A).
- Remove the metal clip and pawls, and then pull out seat cushion outer finisher outside.

Broken Square : Metal clip
Broken Triangle : Pawl

6. Remove the seat cushion outer finisher inside (left).





- Remove the mounting screw (A).





7. Remove the seat slide outer cover (Driver's seat only) mounting screws (A), and then slide to backward.





8. Remove the mounting screw (A) and pawls, and then pull out seat cushion inner finisher outer.

Broken Triangle : Pawl






9. Remove the mounting screw (A), and then pull out seat cushion inner finisher inside (right).





10. Remove the mounting screws (A), and then pull out seat slide inner cover. (Driver's seat only)
11. Remove the seat cushion trim and seat cushion pad. (Without occupant classification system control unit model)
- Remove the seat cushion trim retainer.
- Remove the seat cushion trim and seat cushion pad from the seat cushion frame.
- Remove the hog rings, and separate the seat cushion trim and seat cushion pad.
12. Remove the seat belt buckle. Exploded View
13. Remove the driver seat control unit. Exploded View

Assembly
Assemble in the reverse order of disassembly.

CAUTION:
Install the hog rings of seat cushion trim in position, and then securely connect the trim or trim cord with the pad side wire.