Basic Inspection
INSPECTION AND ADJUSTMENT
Basic Inspection
EXCEPT FLEXIBLE FUEL VEHICLE
1. INSPECTION START
1.Check service records for any recent repairs that may indicate a related malfunction, or a current need for scheduled maintenance.
2.Open engine hood and check the following:
-Harness connectors for improper connections
-Wiring harness for improper connections, pinches and cut
-Vacuum hoses for splits, kinks and improper connections
-Hoses and ducts for leaks
-Air cleaner clogging
-Gasket
3.Confirm that electrical or mechanical loads are not applied.
-Headlamp switch is OFF.
-Air conditioner switch is OFF.
-Rear window defogger switch is OFF.
-Steering wheel is in the straight-ahead position, etc.
4.Start engine and warm it up until engine coolant temperature indicator points the middle of gauge.
Ensure engine stays below 1,000 rpm.
5.Run engine at about 2,000 rpm for about 2 minutes under no load.
6.Make sure that no DTC is displayed with CONSULT or GST.
OK or NG
OK- GO TO 3.
NG- GO TO 2.
2. REPAIR OR REPLACE
Repair or replace components as necessary according to corresponding Diagnostic Procedure.
- GO TO 3.
3. CHECK TARGET IDLE SPEED
With CONSULT
1.Run engine at about 2,000 rpm for about 2 minutes under no load.
2.Rev engine (2,000 to 3,000 rpm) two or three times under no load, then run engine at idle speed for about 1 minute.
3.Read idle speed in "DATA MONITOR" mode with CONSULT. Idle Speed And Ignition Timing Check.
650 ± 50 rpm (in P or N position)
Without CONSULT
1.Run engine at about 2,000 rpm for about 2 minutes under no load.
2.Rev engine (2,000 to 3,000 rpm) two or three times under no load, then run engine at idle speed for about
1 minute.
3.Check idle speed.
Idle Speed And Ignition Timing Check.
650 ± 50 rpm (in P or N position)
OK or NG
OK- GO TO 10.
NG- GO TO 4.
4. PERFORM ACCELERATOR PEDAL RELEASED POSITION LEARNING
1.Stop engine.
2.Perform Accelerator Pedal Released Position Learning.
- GO TO 5.
5. PERFORM THROTTLE VALVE CLOSED POSITION LEARNING
Perform Throttle Valve Closed Position Learning.
- GO TO 6.
6. PERFORM IDLE AIR VOLUME LEARNING
Idle Air Volume Learning.
Is Idle Air Volume Learning carried out successfully?
Yes or No
Yes- GO TO 7.
No- 1.Follow the instruction of Idle Air Volume Learning.
2.GO TO 4.
7. CHECK TARGET IDLE SPEED AGAIN
With CONSULT
1.Start engine and warm it up to normal operating temperature.
2.Read idle speed in "DATA MONITOR" mode with CONSULT.
Idle Speed And Ignition Timing Check.
650 ± 50 rpm (in P or N position)
Without CONSULT
1.Start engine and warm it up to normal operating temperature.
2.Check idle speed.
Idle Speed And Ignition Timing Check.
650 ± 50 rpm (in P or N position)
OK or NG
OK- GO TO 10.
NG- GO TO 8.
8. DETECT MALFUNCTIONING PART
Check the following.
- Check camshaft position sensor (PHASE) and circuit.
- Check crankshaft position sensor (POS) and circuit.
OK or NG
OK- GO TO 9.
NG- 1.Repair or replace.
2.GO TO 4.
9. CHECK ECM FUNCTION
1.Substitute another known-good ECM to check ECM function. (ECM may be the cause of an incident, but this is a rare case.)
2.Perform initialization of NVIS (NATS) system and registration of all NVIS (NATS) ignition key IDs. Refer to
Additional Service When Replacing Control Unit.
- GO TO 4.
10. CHECK IGNITION TIMING
1.Run engine at idle.
2.Check ignition timing with a timing light.
Idle Speed And Ignition Timing Check.
15 ± 5� BTDC (in P or N position)
OK or NG
OK- GO TO 19.
NG- GO TO 11.
11. PERFORM ACCELERATOR PEDAL RELEASED POSITION LEARNING
1.Stop engine.
2.Perform Accelerator Pedal Released Position Learning.
- GO TO 12.
12. PERFORM THROTTLE VALVE CLOSED POSITION LEARNING
Perform Throttle Valve Closed Position Learning.
- GO TO 13.
13. PERFORM IDLE AIR VOLUME LEARNING
Idle Air Volume Learning.
Is Idle Air Volume Learning carried out successfully?
Yes or No
Yes- GO TO 14.
No- 1.Follow the instruction of Idle Air Volume Learning.
2.GO TO 4.
14. CHECK TARGET IDLE SPEED AGAIN
With CONSULT
1.Start engine and warm it up to normal operating temperature.
2.Read idle speed in "DATA MONITOR" mode with CONSULT.
Idle Speed And Ignition Timing Check.
650 ± 50 rpm (in P or N position)
Without CONSULT
1.Start engine and warm it up to normal operating temperature.
2.Check idle speed.
Idle Speed And Ignition Timing Check.
650 ± 50 rpm (in P or N position)
OK or NG
OK- GO TO 15.
NG- GO TO 17.
15. CHECK IGNITION TIMING AGAIN
1.Run engine at idle.
2.Check ignition timing with a timing light.
Idle Speed And Ignition Timing Check.
15 ± 5� BTDC (in P or N position)
OK or NG
OK- GO TO 19.
NG- GO TO 16.
16. CHECK TIMING CHAIN INSTALLATION
Check timing chain installation. Exploded View.
OK or NG
OK- GO TO 17.
NG- 1.Repair the timing chain installation.
2.GO TO 4.
17. DETECT MALFUNCTIONING PART
Check the following.
- Check camshaft position sensor (PHASE) and circuit.
- Check crankshaft position sensor (POS) and circuit.
OK or NG
OK- GO TO 18.
NG- 1.Repair or replace.
2.GO TO 4.
18. CHECK ECM FUNCTION
1.Substitute another known-good ECM to check ECM function. (ECM may be the cause of an incident, but this is a rare case.)
2.Perform initialization of NVIS (NATS) system and registration of all NVIS (NATS) ignition key IDs. Refer to
Description.
- GO TO 4.
19. INSPECTION END
Did you replace ECM, referring this Basic Inspection procedure?
Yes or No
Yes- 1.Perform VIN Registration.
2.INSPECTION END
No-INSPECTION END
FLEXIBLE FUEL VEHICLE
1. INSPECTION START
1.Check service records for any recent repairs that may indicate a related malfunction, or a current need for scheduled maintenance.
2.Open engine hood and check the following:
-Harness connectors for improper connections
-Wiring harness for improper connections, pinches and cut
-Vacuum hoses for splits, kinks and improper connections
-Hoses and ducts for leaks
-Air cleaner clogging
-Gasket
3.Confirm that electrical or mechanical loads are not applied.
-Headlamp switch is OFF.
-Air conditioner switch is OFF.
-Rear window defogger switch is OFF.
-Steering wheel is in the straight-ahead position, etc.
4.Start engine and warm it up until engine coolant temperature indicator points the middle of gauge.
Ensure engine stays below 1,000 rpm.
5.Run engine at about 2,000 rpm for about 2 minutes under no load.
6.Make sure that no DTC is displayed with CONSULT or GST.
OK or NG
OK- GO TO 3.
NG- GO TO 2.
2. REPAIR OR REPLACE
Repair or replace components as necessary according to corresponding Diagnostic Procedure.
- GO TO 3.
3. CHECK TARGET IDLE SPEED
With CONSULT
1.Run engine at about 2,000 rpm for about 2 minutes under no load.
2.Rev engine (2,000 to 3,000 rpm) two or three times under no load, then run engine at idle speed for about 1 minute.
3.Read idle speed in "DATA MONITOR" mode with CONSULT.
Idle Speed And Ignition Timing Check.
650 ± 50 rpm (in P or N position)
Without CONSULT
1.Run engine at about 2,000 rpm for about 2 minutes under no load.
2.Rev engine (2,000 to 3,000 rpm) two or three times under no load, then run engine at idle speed for about
1 minute.
3.Check idle speed.
Idle Speed And Ignition Timing Check.
650 ± 50 rpm (in P or N position)
OK or NG
OK- GO TO 11.
NG- GO TO 4.
4. PERFORM ACCELERATOR PEDAL RELEASED POSITION LEARNING
1.Stop engine.
2.Perform Accelerator Pedal Released Position Learning.
- GO TO 5.
5. PERFORM THROTTLE VALVE CLOSED POSITION LEARNING
Perform Throttle Valve Closed Position Learning.
ECM is displayed refering this procedure-GO TO 6.
ECM is not displayed-GO TO 7.
6. PERFORM ETHANOL MIXTURE RATIO ADAPTATION
Perform Ethanol Mixture Ratio Adaptation (Flexible Fuel Vehicle).
- GO TO 7.
7. PERFORM IDLE AIR VOLUME LEARNING
Idle Air Volume Learning.
Is Idle Air Volume Learning carried out successfully?
Yes or No
Yes- GO TO 8.
No- 1.Follow the instruction of Idle Air Volume Learning.
2.GO TO 4.
8. CHECK TARGET IDLE SPEED AGAIN
With CONSULT
1.Start engine and warm it up to normal operating temperature.
2.Read idle speed in "DATA MONITOR" mode with CONSULT.
Idle Speed And Ignition Timing Check.
650 ± 50 rpm (in P or N position)
Without CONSULT
1.Start engine and warm it up to normal operating temperature.
2.Check idle speed.
Idle Speed And Ignition Timing Check.
650 ± 50 rpm (in P or N position)
OK or NG
OK- GO TO 11.
NG- GO TO 9.
9. DETECT MALFUNCTIONING PART
Check the following.
- Check camshaft position sensor (PHASE) and circuit.
- Check crankshaft position sensor (POS) and circuit.
OK or NG
OK- GO TO 10.
NG- 1.Repair or replace.
2.GO TO 4.
10. CHECK ECM FUNCTION
1.Substitute another known-good ECM to check ECM function. (ECM may be the cause of an incident, but this is a rare case.)
2.Perform initialization of NVIS (NATS) system and registration of all NVIS (NATS) ignition key IDs. Refer to
Special Repair Requirement.
- GO TO 4.
11. CHECK IGNITION TIMING
1.Run engine at idle.
2.Check ignition timing with a timing light.
Idle Speed And Ignition Timing Check.
15 ± 5� BTDC (in P or N position)
OK or NG
OK- GO TO 21.
NG- GO TO 12.
12. PERFORM ACCELERATOR PEDAL RELEASED POSITION LEARNING
1.Stop engine.
2.Perform Accelerator Pedal Released Position Learning.
- GO TO 13.
13. PERFORM THROTTLE VALVE CLOSED POSITION LEARNING
Perform Throttle Valve Closed Position Learning.
ECM is displayed refering this procedure-GO TO 14.
ECM is not displayed-GO TO 15.
14. PERFORM ETHANOL MIXTURE RATIO ADAPTATION
Perform Ethanol Mixture Ratio Adaptation (Flexible Fuel Vehicle).
- GO TO 15.
15. PERFORM IDLE AIR VOLUME LEARNING
Idle Air Volume Learning.
Is Idle Air Volume Learning carried out successfully?
Yes or No
Yes- GO TO 16.
No- 1.Follow the instruction of Idle Air Volume Learning.
2.GO TO 4.
16. CHECK TARGET IDLE SPEED AGAIN
With CONSULT
1.Start engine and warm it up to normal operating temperature.
2.Read idle speed in "DATA MONITOR" mode with CONSULT.
Idle Speed And Ignition Timing Check.
650 ± 50 rpm (in P or N position)
Without CONSULT
1.Start engine and warm it up to normal operating temperature.
2.Check idle speed.
Idle Speed And Ignition Timing Check.
650 ± 50 rpm (in P or N position)
OK or NG
OK- GO TO 17.
NG- GO TO 19.
17. CHECK IGNITION TIMING AGAIN
1.Run engine at idle.
2.Check ignition timing with a timing light.
Idle Speed And Ignition Timing Check.
15 ± 5� BTDC (in P or N position)
OK or NG
OK- GO TO 21.
NG- GO TO 18.
18. CHECK TIMING CHAIN INSTALLATION
Check timing chain installation. Exploded View.
OK or NG
OK- GO TO 19.
NG- 1.Repair the timing chain installation.
2.GO TO 4.
19. DETECT MALFUNCTIONING PART
Check the following.
- Check camshaft position sensor (PHASE) and circuit.
- Check crankshaft position sensor (POS) and circuit.
OK or NG
OK- GO TO 20.
NG- 1.Repair or replace.
2.GO TO 4.
20. CHECK ECM FUNCTION
1.Substitute another known-good ECM to check ECM function. (ECM may be the cause of an incident, but this is a rare case.)
2.Perform initialization of NVIS (NATS) system and registration of all NVIS (NATS) ignition key IDs. Refer to
Special Repair Requirement.
- GO TO 4.
21. INSPECTION END
Did you replace ECM, referring this Basic Inspection procedure?
Yes or No
Yes- 1.Perform VIN Registration.
2.INSPECTION END
No-INSPECTION END