Front Seat

FRONT SEAT

Disassembly and Assembly


SEATBACK (EXCEPT FOLDING SEAT)

Disassembly
1.Remove the utility hook.
Remove the screw. (Passenger's seat only)
2.Remove the seatback trim and seatback pad.





- Remove the seatback retainer (1) on the back side of the seatback.
- Unfasten fastener (2) on the back side of the seatback.
- Remove the hog rings.
- Remove the screw cap.
- Remove the screws, and then remove seatback finisher.
- Remove the side air bag module.





- Remove the side air bag harness connector (A) and clamp.
- Disconnect the seatback heater unit harness connectors (B).





- Remove the headrest holder.

CAUTION:
Before installing headrest holder, check its orientation.
(front/rear and right/left)
- Remove the seatback trim and seatback pad from the seat frame assembly.
- Remove the hog rings to separate the seatback trim and seatback pad.
3.Remove the seatback silencer.
4.Remove the reclining device inner and outer cover.
Assembly
Assemble in the reverse order of disassembly.

CAUTION:
Install the hog rings of seatback trim in position, and then securely connect the trim or trim cord with the pad side wire.

SEAT CUSHION (EXCEPT FOLDING SEAT)

Disassembly

CAUTION:
- Never disassemble seat cushion trim and pad from seat frame assembly of passenger seat. Always replace as an assembly. (With occupant classification system control unit model)
- For front passenger seat service parts, refer to the service part catalogue.
1.Remove the seat cushion outer finisher.
a.Manual seat





- Remove the pawls, and then remove lifter lever knob finisher (1). (Lifter seat only)

Broken triangle indicates : Pawl

- Remove the mounting screws, and remove lifter lever knob (2). (Lifter seat only)





- Pull out the reclining lever knob while holding and raising the pawl.

Broken triangle indicates : Pawl






- Remove the screw (A).
- Remove the metal clip and pawls, and then pull out seat cushion outer finisher.

Broken square indicates : Metal clip
Broken triangle indicates : Pawl

b.Power seat





- Remove the metal clips and pawls, and then pull out seat cushion outer finisher.

Broken square indicates : Metal clip
Broken triangle indicates : Pawl

- Disconnect the harness connectors.
2.Remove the seat belt buckle. Refer to "SEAT BELT BUCKLE : Removal and Installation" Removal And Installation.
3.Remove the seat cushion inner finisher.





Remove the screw (A).
Remove the metal clip and pawls, and then pull out seat cushion inner finisher.

Broken square indicates : Metal clip
Broken triangle indicates : Pawl

4.Remove the seat cushion trim and seat cushion pad. (Without occupant classification system control unit model)
- Remove the seat cushion retainer.
- Disconnect the heater unit harness connector.
- Remove the seat cushion trim and seat cushion pad from the seat frame assembly.
- Remove the hog rings, and separate the seat cushion trim and seat cushion pad.
5.Remove the seat slide outer finisher. (Lifter seat only)





- Remove the screw (A).
- Remove the metal clips, and then pull out seat slide outer finisher.

Broken square indicates : Metal clip

6.Remove the seat cushion front finisher. (Power seat only)





Remove the metal clips and pawls, and the pull out seat cushion front finisher.

Broken square indicates : Metal clip
Broken triangle indicates : Pawl

7.Remove seat slide inner finisher. (Lifter seat only)





- Remove the screw.
- Remove the metal clip, and then pull out seat slide inner finisher.

Broken square indicates : Metal clip

8.Remove the seat cushion outer and inner finisher inside (front).
Remove the screw, and then remove the seat cushion outer and inner finisher inside (front).
9.Remove the seat cushion outer and inner finisher inside (rear).
Remove the metal clip, and then pull out seat cushion outer and inner finisher inside (rear).
Assembly
Assemble in the reverse order of disassembly.

CAUTION:
Install the hog rings of seat cushion trim in position, and then securely connect the trim or trim cord with the pad side wire.

SEATBACK (FOLDING SEAT)

Disassembly
1.Remove the seatback trim and seatback pad.





- Remove the seatback retainer (1) on the back side of the seatback.
- Unfasten fastener (2) on the back side of the seatback.
- Remove the hog rings.
- Remove the screw cap.
- Remove the screws, and then remove seatback finisher.
- Remove the side air bag module.





- Remove the side air bag harness connector (A) and clamp.
- Disconnect the seatback heater unit harness connectors (B).





- Remove the headrest holder.

CAUTION:
Before installing headrest holder, check its orientation.
(front/rear and right/left)
- Remove the seatback trim and seatback pad from the seat frame assembly.
- Remove the hog rings to separate the seatback trim and seatback pad.
2.Remove the seatback silencer.
Assembly
Assemble in the reverse order of disassembly.

CAUTION:
Install the hog rings of seatback trim in position, and then securely connect the trim or trim cord with the pad side wire.

SEAT CUSHION (FOLDING SEAT)

Disassembly

CAUTION:
- Never disassemble seat cushion trim and pad from seat frame assembly of passenger seat. Always replace as an assembly. (With occupant classification system control unit model)
- For front passenger seat service parts, refer to the service part catalogue.
1.Remove the seat cushion outer finisher.





- Pull out the reclining lever knob while holding and raising the pawl.

Broken triangle indicates : Pawl






- Remove the screw (A).
- Remove the metal clips and pawls, and then pull out seat cushion outer finisher.

Broken square indicates : Metal clip
Broken triangle indicates : Pawl

2.Remove the seat belt buckle. Refer to "SEAT BELT BUCKLE : Removal and Installation" Removal And Installation.
3.Remove the seat cushion inner finisher.





Remove the metal clips and pawls, and then pull out seat cushion outer finisher.

Broken square indicates : Metal clip
Broken triangle indicates : Pawl

4.Remove the seat cushion outer finisher inside (upper) and seat cushion inner finisher inside (upper).
5.Remove the seat cushion outer finisher inside (lower).
- Remove the screws.
- Remove the metal clip, and then pull out seat cushion outer finisher inside (lower).
6.Remove the seat cushion inner finisher inside (lower).
- Remove the screws.
- Remove the metal clip, and then pull out seat cushion inner finisher inside (lower).
Assembly
Assemble in the reverse order of disassembly.

CAUTION:
Install the hog rings of seat cushion trim in position, and then securely connect the trim or trim cord with the pad side wire.