Appendix

Model 210 series:

Model 210 series
^ Bending radius (R) of cable should be larger than 130 mm (5.12 in).
^ Cable should not be bent within 50 mm (1.97 in) of end fittings.
^ Grommets should be secured to dash panel after speedometer and cable have been connected.
^ Cable should be aligned and clamped if it has a clamping mark on it.
^ Cable should be clamped with pliers to avoid scratching it.
^ Inner cable should not be withdrawn from transmission side with cable connected to speedometer.

Model Sentra series:

Model Sentra series
^ Bending radius (R) of cable should be larger than 130 mm (5.12 in).
^ Cable should not be bent within 50 mm (1.97 in) of end fittings.
^ Grommets should be secured to dash panel after speedometer and cable have been connected.
^ Cable should be aligned and clamped if it has a clamping mark on it.
^ Cable should be clamped with pliers to avoid scratching it.
^ Inner cable should not be withdrawn from transmission side with cable connected to speedometer.

Model 310 series:

Model 310 series
^ Bending radius (R) of cable should be larger than 130 mm. (5.12 in).
^ Cable should not be bent within 50 mm (1.97 in) of end fittings.
^ Grommets should be secured to dash panel after speedometer and cable have been connected.
^ Cable should be aligned and clamped if it has a clamping mark on it.
^ Cable should be clamped with pliers to avoid scratching it.
^ Inner cable should not be withdrawn from transmission side with cable connected to speedometer.

Model Stanza series:

0GModel Stanza series
^ Bending radius (R) of cable should be larger than 130 mm (5.12 in).
^ Cable should not be bent within 50 mm (1.97 in) of end fittings.
^ Grommets should be secured to dash panel after speedometer and cable have been connected.
^ Cable should be aligned and clamped if it has a clamping mark on it.
^ Cable should be clamped with pliers to avoid scratching it.
^ Inner cable should not be withdrawn from transmission side with cable connected to speedometer.

Model 200SX series:

Model 200SX series
^ Bending radius (R) of cable should be larger than 130 mm (5.12 in).
^ Cable should not be bent within 50 mm (1.97 in) of end fittings.
^ Grommets should be secured to dash panel after speedometer and cable have been connected.
^ Cable should be aligned and clamped if it has a clamping mark on it.
^ Cable should be clamped with pliers to avoid scratching it.
^ Inner cable should not be withdrawn from transmission side with cable connected to speedometer.

Model 720 series:

Model 720 series
^ Bending radius (R) of cable should be larger than 130 mm (5.12 in).
^ Cable should not be bent within 50 mm (1.97 in) of end fittings.
^ Grommets should be secured to dash panel after speedometer and cable have been connected.
^ Cable should be aligned and clamped if it has a clamping mark on it.
^ Cable should be clamped with pliers to avoid scratching it.
^ Inner cable should not be withdrawn from transmission side with cable connected to speedometer.

Model Maxima series:

Model Maxima series
^ Bending radius (R) of cable should be larger than 130 mm (5.12 in).
^ Cable should not be bent within 50 mm (1.97 in) of end fittings.
^ Grommets should be secured to dash panel after speedometer and cable have been connected.
^ Cable should be aligned and clamped if it has a clamping mark on it.
^ Cable should be clamped with pliers to avoid scratching it.
^ Inner cable should not be withdrawn from transmission side with cable connected to speedometer.

Model 28OZX series:

Model 28OZX series
^ Bending radius (R) of cable should be larger than 130 mm (5.12 in).
^ Cable should not be bent within 50 mm (1.97 in) of end fittings.
^ Grommets should be secured to dash panel after speedometer and cable have been connected.
^ Cable should be aligned and clamped if it has a clamping mark on it.
^ Cable should be clamped with pliers to avoid scratching it.
^ Inner cable should not be withdrawn from transmission side with cable connected to speedometer.