Operation CHARM: Car repair manuals for everyone.

Scan Tool Testing and Procedures





SYSTEM DESCRIPTION
The ECM controls the cooling fan corresponding to the vehicle speed, engine coolant temperature and air conditioner ON signal. The control system has 3-step control [HIGH/LOW/OFF].






Operation






ECM TERMINALS AND REFERENCE VALUE
Specification data are reference values, and are measured between each terminal and (25) (ECCS ground).






ON BOARD DIAGNOSIS LOGIC
If the cooling fan or another component in the cooling system malfunctions, the engine coolant temperature will rise.
When the engine coolant temperature reaches an abnormally high temperature condition, a malfunction is indicated.

CAUTION: When a malfunction is indicated, be sure to replace the coolant following the procedure in the MA section ("Changing Engine Coolant", "ENGINE MAINTENANCE"). Also, replace the engine oil.
a. Fill radiator with coolant up to specified level with a filling speed of 2 liters per minute like pouring coolant by kettle. Be sure to use coolant with the proper mixture ratio.
b. After refilling coolant, run engine to ensure that no water-flow noise is emitted.


OVERALL FUNCTION CHECK

WARNING: Never remove the radiator cap when the engine is hot. Serious burns could be caused by high pressure fluid escaping from the radiator. Wrap a thick cloth around cap. Carefully remove the cap by turning it a quarter turn to allow built-up pressure to escape. Then turn the cap all the way off.

1) Check the coolant level in the reservoir tank and radiator. Allow engine to cool before checking coolant level. If the coolant level in the reservoir tank and/or radiator is below the proper range, skip the following steps and go to "DIAGNOSTIC PROCEDURE".
2) Confirm whether customer filled the coolant or not. If customer filled the coolant, skip the following steps and go to "DIAGNOSTIC PROCEDURE".









With CONSULT
3) Turn ignition switch "ON".
4) Perform "COOLING FAN" in "ACTIVE TEST" mode with CONSULT (LOW speed and HI speed).


- - - OR - - -









Without TOOLS
3) Start engine.
Be careful not to overheat engine.

4) Set temperature control lever to full cold position.
5) Turn air conditioner switch "ON".
6) Turn blower fan switch "ON".
7) Run engine at idle for a few minutes with air conditioner operating.
Be careful not to overheat engine.

8) Make sure that cooling fan operates at low speed.
9) Turn ignition switch "OFF".
10) Turn air conditioner switch and blower fan switch "OFF".
11) Disconnect engine coolant temperature sensor harness connector.
12) Connect 150 ohms resistor to engine coolant temperature sensor harness connector.
13) Restart engine and make sure that cooling fan operates at higher speed than low speed.
Be careful not to overheat engine.









Electrical Diagrams









Circuit Connectors


Overheat (1 Of 3):




Overheat (2 Of 3):




Overheat (3 Of 3):





DIAGNOSTIC PROCEDURE


Overheat Procedure "A" (1 Of 2):




Overheat Procedure "A" (2 Of 2):





Procedure A


Overheat Procedure "B" (1 Of 2):




Overheat Procedure "B" (2 Of 2):




Procedure B

Final Check
Perform FINAL CHECK by the following procedure after repair is completed.
1. Warm up engine. Run the vehicle at least 20 minutes. Pay attention to engine coolant temperature gauge on the instrument panel. If the reading shows an abnormally high temperature, another part may be malfunctioning.
2. Stop vehicle and let engine idle. Check the intake and exhaust systems for leaks by listening for noise or visually inspecting the components.
3. Allow engine to cool and visually check for oil and coolant leaks. Then, perform "OVERALL FUNCTION CHECK".






MAIN 12 CAUSES OF OVERHEATING


COMPONENT INSPECTION









Cooling fan relay-1
Check continuity between terminals (3) and (5).









Cooling fan relays -2 and -3
Check continuity between terminals (3) and (5), (6) and (7).
If NG, replace relay.









Cooling fan motors -1 and -2
1. Disconnect cooling tan motor harness connectors.
2. Supply cooling fan motor terminals with battery voltage and check operation.

Cooling fan motor should operate.
If NG, replace cooling fan motor.