Vanity Lamp: Description and Operation
System DescriptionWITHOUT POWER DOOR LOCKS
Power Supply and Ground
Power is supplied at all times:
- through 10 A fuse [No.13, located in the fuse block (J/B)]
- to interior lamp terminal (+).
When interior lamp switch is in the DOOR position and any door is opened, ground is supplied to interior lamp through the door switches.
When interior lamp switch is in the ON position, ground is supplied:
- through case ground of interior lamp
- to interior lamp.
WITH POWER DOOR LOCKS AND WITHOUT MULTI-REMOTE CONTROL SYSTEM
Power Supply and Ground
Power is supplied at all times:
- through 10 A fuse (No.13, located in the fuse block (J/B)]
- to time control unit terminal 2 and
- to trunk room lamp terminal 1.
Power is supplied at all times:
- through 10 A fuse [No.12, located in the fuse block (J/B)]
- to key switch terminal 2.
When the key is removed from ignition key cylinder, power is interrupted:
- through key switch terminal 1
- to time control unit terminal 11.
With the ignition key switch in the ON or START position, power is supplied:
- through 10 A fuse [No.10, located in the fuse block (J/B)]
- to time control unit terminal 13.
Ground is supplied:
- to time control unit terminal 6
- through body grounds M28 and M54.
When the front driver side door is opened, ground is supplied:
- through body grounds B13 and B19
- to front door switch LH terminal 3
- from front door switch LH terminal 2
- to time control unit terminal 7.
When any other door (except front driver side door) is opened, ground is supplied to time control unit terminal 9.
When the front driver side door is unlocked, the time control unit receives a ground signal:
- through body grounds M28 and M54
- to front door lock actuator LH (door unlock sensor) terminal 4
- from front door lock actuator LH (door unlock sensor) terminal 2
- to time control unit terminal 22.
When a signal, or combination of signals is received by the time control unit, ground is supplied:
- through time control unit terminal 16
- to interior lamp terminal DR.
With power and ground supplied, the interior lamp illuminates.
Switch Operation
When interior lamp switch is in the ON position, ground is supplied:
- through case ground of interior lamp
- to interior lamp.
Power is supplied:
- to interior lamp terminal (+)
- from time control unit terminal 3.
When map lamp (LH and/or RH) is ON, ground is supplied:
- through body grounds M28 and M54
- to map lamp terminal (-).
Power is supplied:
- to map lamp terminal (+)
- from time control unit terminal 3.
When vanity lamp (LH and/or RH) is ON, ground is supplied:
- through body grounds M28 and M54
- to vanity lamps (LH and RH) terminal 2.
Power is supplied:
- to vanity lamps (LH and RH) terminal 1
- from time control unit terminal 3.
When trunk room lamp switch is ON (trunk lid is opened), ground is supplied:
- through body grounds B13 and B19
- to trunk room lamp switch terminal (-)
- from trunk room lamp switch terminal (+)
- to trunk room lamp terminal 2
With power and ground supplied, interior lamps turn ON.
Interior Lamp Timer Operation
When interior lamp switch is in the "DOOR" position, the time control unit keeps the interior lamp illuminated for about 30 seconds when:
- unlock signal is supplied from driver door unlock sensor while all doors are closed and key is out of ignition key cylinder
- key is removed from ignition key cylinder while all doors are closed
- driver door is opened and then closed while key is out of the ignition key cylinder. (However, if the driver door is closed with the key inserted in the ignition key cylinder after the driver door is opened with the key removed, the timer is operated.)
The timer is canceled when:
- driver door is locked,
- driver door is opened, or
- ignition switch is turned ON.
ON-OFF Control
When the front driver side door, front passenger door, rear LH or RH door is opened, the interior room lamp turns on while the interior room lamp switch is in the "DOOR" position.
Battery Saver
The lamp turns off automatically when interior lamp, map lamp, and/or vanity lamps are illuminated with the ignition key in OFF position, if the lamp remains lit by the door switch open signal or if the lamp switch is in ON position for approximately 10 minutes.
After lamps turn OFF by the battery saver system, the lamps illuminate again when:
- driver door is locked or unlocked,
- door is opened or closed,
- key is inserted in or removed from ignition key cylinder.
WITH MULTI-REMOTE CONTROL SYSTEM
Power Supply and Ground
Power is supplied at all times:
- through 10 A fuse (No.37, located in the fuse and fusible link box)
- to smart entrance control unit terminal 10.
Power is supplied at all times:
- through 10 A fuse [No.12, located in the fuse block (J/B)]
- to key switch terminal 2 and
- through 10 A fuse [No.13, located in the fuse block (J/B)]
- to trunk room lamp terminal 1.
When the key is removed from ignition key cylinder, power is interrupted:
- through key switch terminal 1
- to smart entrance control unit terminal 32.
With the ignition key switch in the ON or START position, power is supplied:
- through 10 A fuse [No. 10, located in the fuse block (J/B)]
- to smart entrance control unit terminal 33.
Ground is supplied:
- to smart entrance control unit terminal 16
- through body grounds M28 and M54.
When the front driver side door is opened, ground is supplied:
- through body grounds B13 and B19
- to front door switch LH terminal 3
- from front door switch LH terminal 2
- to smart entrance control unit terminal 29.
When any other door (except front driver side door) is opened, ground is supplied to smart entrance control unit terminal 28
When the front driver side door is unlocked, the smart entrance control unit receives a ground signal:
- through body grounds M28 and M54
- to front door lock actuator LH (door unlock sensor) terminal 4
- from front door lock actuator LH (door unlock sensor) terminal 2
- to smart entrance control unit terminal 36.
When a signal, or combination of signals is received by the smart entrance control unit, ground is supplied:
- through smart entrance control unit terminal 8
- to interior lamp terminal DR.
With power and ground supplied, the interior lamp illuminates.
Switch Operation
When interior lamp switch is in the ON position, ground is supplied:
- through case ground of interior lamp
- to interior lamp.
Power is supplied:
- to interior lamp terminal (+)
- from smart entrance control unit terminal 17.
When map lamp (LH and/or RH) is ON, ground is supplied:
- through body grounds M28 and M54
- to map lamp terminal (-).
Power is supplied:
- to map lamp terminal (+)
- from smart entrance control unit terminal 17.
When vanity lamp (LH and/or RH) is ON, ground is supplied:
- through body grounds M28 and M54
- to vanity lamps (LH and RH) terminal 2.
Power is supplied:
- to vanity lamps (LH and RH) terminal 1
- from smart entrance control unit terminal 17.
When trunk room lamp switch is ON (trunk lid is opened), ground is supplied:
- through body grounds B13 and B19
- to trunk room lamp switch terminal (-)
- from trunk room lamp switch terminal (+)
- to trunk room lamp terminal 2
With power and ground supplied, interior lamps turn ON.
Interior Lamp Timer Operation
When interior lamp switch is in the "DOOR" position, the smart entrance control unit keeps the interior lamp illuminated for about 30 seconds when:
- unlock signal is supplied from driver door unlock sensor while all doors are closed and key is out of ignition key cylinder
- key is removed from ignition key cylinder while all doors are closed
- driver door is opened and then closed while key is out of the ignition key cylinder. (However, if the driver door is closed with the key inserted in the ignition key cylinder after the driver door is opened with the key removed, the timer is operated.)
When interior lamp switch is in the "DOOR" position and unlock signal is supplied from multi-remote controller while driver side door is locked and all doors are closed (even if key is inserted), the smart entrance control unit keeps the interior lamp illuminated for about 30 seconds.
The timer is canceled when:
- driver door is locked,
- driver door is opened, or
- ignition switch is turned ON.
ON-OFF Control
When the front driver side door, front passenger door, rear LH or RH door is opened, the interior room lamp turns on while the interior room lamp switch is in the "DOOR" position.
Battery Saver
The lamps turn off automatically when interior lamp, map lamp and/or vanity lamps are illuminated with the ignition key in OFF position, if the lamp remains lit by the door switch open signal or if the lamp switch is in ON position for approximately 10 minutes.
After lamps turn OFF by the battery saver system, the lamps illuminate again when:
- driver door is locked or unlocked,
- door is opened or closed,
- key is inserted in or removed from ignition key cylinder.