Engine: Service Precautions
Precautions for Draining Coolant^ Drain coolant when engine is cooled.
Precautions for Disconnecting Fuel Piping
^ Before starting work, make sure no fire or spark producing items are in the work area.
^ Release fuel pressure before any removal or disassembly.
^ After disconnecting pipes, plug openings to stop fuel leakage.
Precautions for Removal and Disassembly
^ When instructed to use special service tools, use the specified tools. Always be careful to work safely, avoid forceful operations.
^ Use maximum care to avoid damage to mating or sliding surfaces.
^ Cover openings of engine system with tape or equivalent, if necessary, to seal out foreign materials.
^ Mark and arrange disassembly parts in an organized way for easy troubleshooting and assembly.
^ When loosening nuts and bolts, as a basic rule, start with the one furthest outside, then the one diagonally opposite, and so on. If the order of loosening is specified, follow the specifications.
Precautions for Inspection, Repair and Replacement
^ Before repairing or replacing, thoroughly inspect parts. Inspect new replacement parts in the same way, and replace if necessary.
Precautions for Assembly and Installation
^ Use torque wrench to tighten bolts or nuts.
^ When tightening nuts and bolts, as a basic rule, equally tighten in several different steps starting with the ones in center, then ones on inside and outside diagonally in this order. If the order of tightening is specified, follow the specifications.
^ Always replace the old with a new gasket, packing, oil seal or O-ring.
^ Thoroughly wash, clean, and air-blow each part. Carefully check oil or coolant passages for any restriction and blockage.
^ Avoid damaging sliding or mating surfaces. Completely remove foreign materials such as cloth lint or dust. Before assembly, oil sliding surfaces well.
^ Bleed the air trapped within the system after draining the coolant.
^ After repairing, start engine and increase engine speed to check coolant, fuel, oil, and exhaust systems for leakage or rattles.
Parts Requiring Angular Tightening
^ Use an angle wrench for the final tightening of the following engine parts.
- Cylinder head bolts
- Lower cylinder block bolts
- Connecting rod cap bolts
- Crankshaft pulley bolt (No angle wrench is required as the bolt flange is provided with notches for angular tightening)
^ Do not use a torque value for final tightening.
^ The torque value for these parts are for a preliminary step.
^ Ensure thread and seat surfaces are clean and coated with engine oil.
Precautions for Liquid Gasket
REMOVAL OF LIQUID GASKET SEALING
^ After removing the mounting bolts and nuts, disconnect the component using a seal cutter.
CAUTION: Be careful not to damage the mating surfaces.
^ In areas where the cutter is difficult to use, use a plastic hammer to lightly tap the areas where the sealant is applied to disconnect the component.
CAUTION: If for some unavoidable reason a tool such as a flat-bladed screwdriver is used, be careful not to damage the mating surfaces.
LIQUID GASKET APPLICATION PROCEDURE
1. Using a scraper, remove the old RTV Silicone Sealant adhering to the gasket application surface and the mating surface.
^ Remove the sealant completely from the groove of the gasket application surface, mounting bolts, and bolt holes.
2. Thoroughly clean the gasket application surface and the mating surface and remove adhering moisture, grease and foreign materials.
3. Attach the sealant tube to the tube presser. Use Genuine RTV Silicone Sealant or equivalent.
4. Apply the sealant without breaks to the specified location with the specified dimensions.
^ If there is a groove for the sealant application, apply the sealant to the groove.
^ As for the bolt holes, normally apply the sealant inside the holes. If specified, it should be applied outside the holes.
^ Within five minutes of the sealant application, install the mating component.
^ If the sealant protrudes, wipe it off immediately.
^ Do not retighten after the installation.
^ After 30 minutes or more have passed from the installation, fill the engine with the specified oil and coolant.
CAUTION: Follow all specific instructions.