Function of Center Switch
FUNCTION OF CENTER SWITCHDisplay with Pushed "DEST" button
- Easy Mode ("Short Menus" ON)
- Expert Mode ("Short Menus" OFF)
The function of each icon is as given:
Display with Pushed "ROUTE" button
- Easy Mode ("Short Menus" ON)
- Expert Mode ("Short Menus" OFF)
The function of each icon is as given:
Display with Pushed "SETTING" button
The function of each icon is as given:
Display Settings
How To Perform Display Setting
1. Start the engine.
2. Push "SETTING" button.
3. Select "Display" with enter button.
Brightness/Contrast/Map Back ground
How To Perform Navigation Setting
1. Select "Brightness/Contrast/Map Background".
- Brightness, Contrast and Background are shown at the lower part of the screen, and it can be set with the joystick.
Display Off
How To Perform Navigation Setting
1. Select "Display Off".
- When setting is turned on (Indicator light ON), the display will be under sleep mode.
Vehicle Electronic Systems
Vehicle Electronic Systems:
Application Items:
How To Perform Navigation Setting
1. Start the engine.
2. Push "SETTING" button.
3. Select "Vehicle Electronic Systems".
System Settings
How To Perform System Setting
1. Start the engine.
2. Push "SETTING" button.
3. Select "System Settings".
Language Setting
How To Perform Language Setting
1. Select "Language/Unit".
- Language setting can be switched.
- Unit setting can be changed.
Clock Settings
How To Perform Clock Setting
1. Select "Clock".
- Select the "Hours" or "Minutes" key and tilt the joystick to the left or the right to adjust the time.
- Turn ON and OFF daylight saving time.
- Select the "Auto Adjust" key. The time will be reset to the GPS time.
- Select the "Select Time Zone" key. The [TIME ZONE] screen will appear.
Beep Setting
How To Perform Beep Setting
1. Select "Beep Setting".
- When Beep Setting is on (indicator light on), a beep will sound if the button is pushed.
NOTE:
Items in exception of Beep Setting ON/OFF.
- An error beep.
- An interrupted-screen beep.
Navigation Setting
How To Perform Navigation Setting
1. Start the engine.
2. Push "SETTING" button.
3. Select "NAVIGATION".
"VIEW" MODE
Select "Birdview" or "Plan View" icon.
- To open the map screen display with Birdview, select "Birdview".
- To open the map screen display with Plan View, select "Plan View".
"HEADING" MODE
- To display North up, select "North up".
- To display the car heading up, select "Heading up".
"NEARBY DISPLAY ICONS" MODE
- Select an icon to display on the map screen.
"SAVE CURRENT LOCATION" MODE
- The current vehicle location can be registered in "Address Book".
NOTE: "Address Book" can store 50 items maximum.
"ADJUST CURRENT LOCATION" MODE
1. Move marker to correct location.
2. Select "SET" and the vehicle location mark will be located in current position.
3. Select an icon "right" or "left" to calibrate the heading direction.
(Arrow marks will rotate corresponding to the calibration key.)
4. Select "Set". Then the vehicle mark will be matched to the arrow mark.
"AUTO RE-ROUTE" MODE
- To activate "AUTO RE-ROUTE" mode, select "On".
- To deactivate "AUTO RE-ROUTE" mode, select "Off".
"AVOID AREA SETTINGS" MODE
- Areas to avoid can be registered.
"CLEAR MEMORY" MODE
- To delete all the stored places in "Address Book", "Avoid Area" and "Previous Destinations", select "Yes".
"EDIT ADDRESS BOOK" MODE
- Edit the items registered in Address Book.
"GPS INFORMATION" MODE
- Latitude, longitude, altitude, astrometric state, and satellite location are displayed as GPS information.
NOTE: Altitude is displayed only in three-dimensional status.
"QUICK STOP CUSTOMER SETTING" MODE
- Select a category for the "Quick Stop" menu.
NOTE: This only replaces the fifth position on the "QUICK STOP" menu when "ROUTE" is pressed.
"SET AVERAGE SPEED" MODE
- Set the average vehicle speed to calibrate the estimated journey time for the destination.
- Set three items: "Freeway", "Main Roads", and "Ordinary Roads".
"TRACKING" MODE
- To delete the tracking marks on the map, select "Off".
- To leave the tracking marks on the map, select "On".
NOTE: When a trail display is turned OFF, trail data is erased from the memory.
GUIDANCE VOLUME
Description
Following guidance volume settings can be changed.
Activation/Deactivation Setting
- The voice prompt can be turned on/off by pressing the "Guidance Volume" button.
Voice Volume Setting
- Volume of the voice can be controlled by tilting the joystick to left/right.
DISPLAY WITH PUSHED "TRIP" BUTTON
- When the "TRIP" button is pushed, the following items will display on the screen.
- Warning message (if there are any) -> TRIP1 -> TRIP2 -> FUEL ECONOMY -> MAINTENANCE -> OFF.
TRIP 1 OR TRIP 2
- Elapsed time, Driving distance and Average speed are displayed as Trip 1 information or Trip 2 information.
- The way to reset is by pushing the "Reset" switch or by keeping pushing "TRIP" button more than 1.5 seconds.
FUEL ECONOMY
- Average Fuel Economy, Distance to Empty, Fuel Economy are displayed as Fuel Economy information.
- The way to reset is by pushing the "Reset" switch or by keeping pushing "TRIP" button more than 1.5 seconds.
MAINTENANCE
- Engine Oil and Tire Rotation are displayed as Maintenance information.
ENGINE OIL OR TIRE ROTATION
- Possible to set up interval of engine oil and tire rotation by tilting joystick right and left.
WARNING INDICATIONS
Warning signal (Door switch signal) is received from BCM through CAN communication line.