Part 2

Assembly (2)














46. Tighten transaxle case cover bolts to specified torque. Refer to "Components".

CAUTION: Do not reuse seal bolts.





47. Install new governor apply gasket.

NOTE:
^ Do not reuse governor apply gaskets.
^ Apply petroleum jelly to governor apply gaskets.





48. Install seminal cord assembly.

CAUTION: Be careful not to break the solenoid connector and A/T fluid temperature sensor.

NOTE: Apply ATF to O-ring.





49. While holding control valve assembly, connect the parking lock rod sub assembly to manual valve lever sub assembly.

NOTE: Shift position is "N".








50. Tighten control valve assembly bolts to specified torque. Refer to "Components".





51. Install suction cover and new suction cover gasket in control valve assembly.

NOTE: Do not reuse suction cover gasket.





52. Tighten new suction cover gasket and suction cover bolts to specified torque. Refer to "Components".





53. Install sensor clamp and A/T fluid temperature sensor in control valve assembly.





54. Tighten sensor clamp bolts to specified torque. Refer to "Components".





55. Connect the solenoid connectors.





56. Apply silicone RTV to side cover as shown. Refer to "Recommended Chemical Products and Sealants".

CAUTION: Complete remove all moisture, oil and sealant, etc. From side cover and transaxle case.





57. Install side cover in transaxle case.





58. Tighten side cover torx bolts to specified torque. Refer to "Components".

NOTE: Do not reuse seal bolt.





59. Install new O-rings in ATF cooler assembly.

NOTE:
^ Do not reuse O-rings.
^ Apply ATF to O-rings.

60. Install ATF cooler assembly, washer and new spring washer.

CAUTION: Do not reuse spring washer.

61. Tighten hexagon bolt specified torque. Refer to "Components".








62. Install PNP switch to manual valve lever sub assembly.
63. Temporary tightening the bolts.





64. Install washer plate and lock washer.

NOTE: Do not reuse washer plate and lock washer.

65. Tighten nut specified torque. Refer to "Components".





66. Install alignment tool.
67. Adjust PNP switch so that alignment tool pointer aligns with neutral base line on PNP switch body.





68. Tighten PNP switch bolts to specified torque. Refer to "Components".





69. Bend the lock washer using a flat-bladed screwdriver.





70. Install range lever in manual valve lever sub assembly.
71. Tighten range lever nut to specified torque. Refer to "Components".





72. Install turbine revolution sensor in transaxle case.
73. Tighten turbine revolution sensor bolt to specified torque. Refer to "Components".

NOTE:
^ Do not reuse seal bolt.
^ Apply ATF to O-ring.





74. Install revolution sensor in transaxle case.
75. Tighten revolution sensor bolt to specified torque. Refer to "Components".

NOTE:
^ Do not reuse seal bolt.
^ Apply ATF to O-ring.





76. Install new O-ring in A/T fluid charging pipe.

NOTE:
^ Do not reuse O-ring.
^ Apply petroleum jelly to O-ring.

77. Install A/T fluid charging pipe in transaxle housing.
78. Install A/T fluid cooler tube.

NOTE: Do not reuse copper washer.

79. Tighten A/T fluid cooler tube union to specified torque. Refer to "Components".
80. Install air breather hose.
81. Install A/T fluid level gauge.
82. Install drain plug in transaxle housing.
83. Tighten drain plug to specified torque. Refer to "Components".

NOTE: Do not reuse drain plus Basket.





84. Install torque converter.





85. Check the dimension of "C".
Dimension "C": 14.0 mm (0.55 inch)

CAUTION: If the distance is out of standards, adjust within standards again.