Removal And Installation

INSTRUMENT PANEL ASSEMBLY

Instrument Panel

Exploded View IP-10 (Part 1):

Exploded View IP-10 (Part 2):

COMPONENTS







WORK STEPS
When removing instrument panel & pad, cluster lid A, cluster lid C, passenger air bag module assembly and center console assembly, follow steps in the order shown.

CAUTION:
- Disconnect both battery cables.
- Never tamper with or force air bag lid open, as this may adversely affect air bag performance.
- Be careful not to scratch pad and other parts.

Removal




1. Pull instrument finisher E backward by approximately 30° while disengaging the instrument finisher E metal clips and pawl.




2. Remove cluster lid C.
a. Remove cluster lid C screws.
b. Pull back and disengage pawls and cluster lid C metal clips.
c. Disconnect harness connector and then remove cluster lid C.

3. Remove audio unit.
4. Remove front pillar garnish.




5. Remove the side panel (LH/RH).
a. Pull up instrument side panel and disengage pawls.
b. Remove instrument side panel.




6. Remove instrument side mask (LH/RH).
a. Insert a suitable tool into upper space of instrument mask.
b. Disengage pawls, and then remove instrument side mask.




7. Remove instrument side finisher.
a. Insert a suitable tool into space of instrument side finisher.
b. Disengage instrument side finisher metal clips, and then remove instrument side finisher.




8. Remove side ventilator assembly (LH).
a. Insert a suitable tool into the bottom gap of side ventilator assembly after removing the instrument side mask and push against A and B as shown to disengage the pawls.




b. Lift the side ventilator up from the bottom, pull backward while disengaging the side ventilator assembly upper pawls, and then remove the side ventilator.

9. Remove steering lock escutcheon.
10. Remove screws, and disengage pawls then remove the steering column cover.




11. Remove cluster lid A.
a. Remove screws from instrument upper panel right side.




b. Lift the instrument upper panel up, disengage metal clips.
c. Pull backward and disengage clips.
d. Remove cluster lid A.

12. Remove combination meter.




13. Remove instrument lower finisher.
a. Disengage pawls and remove fuse block lid.
b. Remove the screws.
c. Pull backward while disengaging the instrument lower finisher clip and pawls.
d. Disconnect in-vehicle sensor and harness connector, and then remove instrument lower finisher.

14. Remove glove box.




15. Remove side ventilator assembly.
a. Insert a suitable tool into the side ventilator assembly from center console side, disengage the clips and pawl of instrument panel pad.




b. Reach through the glove box compartment by hand to the backside of the side ventilator and push against A as shown to engage the pawl.
c. Insert a suitable tool into the bottom gap of side ventilator assembly after removing the instrument side mask and push against B as shown to disengage the pawl.




d. Lift the side ventilator assembly up from the bottom, pull backward while disengaging the side ventilator assembly upper pawls, and then remove the side ventilator assembly.

16. Remove front passenger air bag module.




17. Remove instrument upper mask.
a. Insert a remover into backside space of instrument upper mask.
b. Disconnect harness connector, and then remove instrument upper mask.




18. Remove instrument finisher D.
a. Insert a remover into upper space of instrument finisher D.
b. Disengage clips and pawls, then remove instrument finisher D.

19. Remove controller.




20. Remove instrument upper panel assembly.
a. Remove bolts and screws.
b. Pull backward and remove instrument upper panel assembly.

21. Remove lighting & turn signal switch.
22. Remove wiper & washer switch.
23. Remove hood opener handle and fuel filler lid opener handle. Refer to Hood Lock Control".
24. Remove screws, and then remove instrument panel & pad from passenger door opening portion.

Installation
Installation is in the reverse order of removal.

CLUSTER LID A

Removal




1. Pull instrument finisher E backward by approximately 30 degrees while disengaging the metal clips and pawl.

2. Remove front pillar garnish.




3. Pull up instrument side panel and disengage pawls.
4. Remove instrument side panel.




5. Insert a remover into upper space of instrument mask.
6. Disengage pawls, and then remove instrument side mask.




7. Insert a remover into space of instrument side finisher.
8. Disengage metal clips, and then remove instrument side finisher.




9. Insert suitable tool into the bottom gap of side ventilator assembly after removing the instrument side mask, push against A and B as shown to disengage the pawls.




10. Lift the side ventilator up from the bottom, pull backward while disengaging the side ventilator assembly's upper pawls, and then remove the side ventilator.
11. Remove screws, and disengage pawls.
12. Remove steering column cover upper.




13. Remove screws from instrument upper panel right side.




14. Lift the instrument upper panel up, disengage metal clips.
15. Pull backward and disengage clips.
16. Remove cluster lid A.

Installation
Installation is in the reverse order of removal.

CLUSTER LID C

Removal




1. Pull instrument finisher E backward by approximately 30 degrees while disengaging the metal clips and pawl.




2. Remove screws.
3. Pull back, and disengage pawls and metal clips.
4. Disconnect harness connector, and then remove cluster lid C.

Installation
Installation is in the reverse order of removal.

COMBINATION METER

Removal




1. Pull instrument finisher E backward by approximately 30 degrees while disengaging the metal clips and pawl.
2. Remove front pillar garnish.




3. Pull up instrument side panel and disengage pawls.
4. Remove instrument side panel.




5. Insert a remover into upper space of instrument mask.
6. Disengage pawls, and then remove instrument side mask.




7. Insert a remover into space of instrument side finisher.
8. Disengage metal clips, and then remove instrument side finisher.




9. Insert suitable tool into the bottom gap of side ventilator assembly after removing the instrument side mask, push against A and B as shown to disengage the pawls.




10. Lift the side ventilator up from the bottom, pull backward while disengaging the side ventilator assembly's upper pawls, and then remove the side ventilator.
11. Remove screws, and disengage pawls.
12. Remove steering column cover upper.




13. Remove screws from instrument upper panel right side.




14. Lift the instrument upper panel up, disengage metal clips.
15. Pull backward and disengage clips.
16. Remove cluster lid A.




17. Remove screws (A) and metal clip (B), and remove combination meter.

Installation
Installation is in the reverse order of removal.

GLOVE BOX ASSEMBLY

Removal




1. Remove glove box screws.
2. Pull backward while disengaging the glove box assembly pawls.
3. Disconnect lamp harness connector, and then remove glove box assembly.

Installation
Installation is in the reverse order of removal.

INSTRUMENT LOWER FINISHER

Removal




1. Pull backward while disengage the instrument lower finisher's clip and pawls.
2. Disconnect in-vehicle sensor and harness connector, and then remove instrument lower finisher.

Installation
Installation is in the reverse order of removal.

CENTER CONSOLE ASSEMBLY




Removal
1. Insert a suitable tool into front side space of console mask, and disengage metal clips.
2. Disconnect harness connector, and then remove console mask.




3. Place the selector lever in "D" position (A/T and CVT only).
4. Remove selector lever knob (A/T and CVT only).
5. Pull up and disengage A/T and CVT console finisher metal clips (A/T and CVT only).
6. Remove A/T and CVT console finisher (A/T and CVT only).
7. Remove shift knob (M/T only).
8. Pull up and disengage M/T console boot metal clips (M/T only)




9. Remove M/T console boot (M/T only).
10. Disengage console rear finisher metal clips and pawl.
11. Remove console rear finisher.




12. Disengage console mask cover metal clips and pawls, and then remove console mask cover (with armrest).




13. Disengage rear cup holder metal clips and pawls (without armrest).
14. Remover rear cup holder (without armrest).
15. Remove console body assembly screws and nut.
16. Disconnect harness connector, and then remove console body assembly.




17. Remove both of the instrument lower cover LH and RH clips.
18. Disengage instrument lower cover LH and RH metal clips and remove both of the instrument lower cover LH and RH.
19. Remove screws and then remove center console.

Installation
Installation is in the reverse order of removal.