Fuel Tank: Service and Repair
FUEL TANKExploded View FL-9:
Component
Removal and Installation
REMOVAL
WARNING: Be sure to read "General Precautions" when working on the fuel system. Refer to "General Precaution".
1. Drain fuel from fuel tank if necessary.
CAUTION:
- Because fuel tank becomes unstable when installing/removing, fuel should be drained if the level exceeds specification Refer to, "Fuel Level Sensor Unit, Fuel Filter And Fuel Pump Assembly".
- Situate vehicle on a flat and solid surface.
2. Open fuel door and unscrew the fuel filler cap to release the pressure inside the fuel tank.
3. Release the fuel pressure from the fuel lines. Refer to EC-78 "Fuel Pressure Check". Testing and Inspection
4. Remove rear seat bottom.
5. Turn the three retainers 90 degree in a clockwise direction and remove the fuel pump inspection hole cover.
Disconnect electrical connector (A) and fuel feed hose quick connector (B).
- Fuel feed hose (1)
- Disconnect the quick connector using the following procedure.
- Hold the sides of the connector, push in tabs and pull out the tube.
- If quick connector and tube on fuel pump assembly are stuck, push and pull several times until they move. Disconnect them by pulling.
CAUTION:
- The tube can be removed when the tabs are completely depressed. Do not twist it more than necessary.
- Do not use any tools to remove the quick connector.
- Keep resin tube away from heat. Be especially careful when welding near the resin tube.
- Prevent acid liquid such as battery electrolyte, from getting on resin tube.
- Do not bend or twist resin tube during installation and removal.
- To keep the connecting portion clean, free of foreign materials and to avoid damage, cover them completely with plastic bags or something similar.
- Do not insert plug to prevent damage to O-ring in quick connector.
6. Remove center exhaust tube.
7. Remove exhaust heat shields.
8. Disconnect parking brake cables (1) from the lower surface of fuel tank and axle and position the parking brake cables (1) out of the way.
9. Remove brake tube protector (1) from rear axle (2).
10. Loosen fuel filler hose clamp (3) and remove fuel filler hose (1) from fuel tank (2).
CAUTION: Do not remove fuel filler hose (1) from fuel filler tube. Do not allow contact with the suspension during installation. When removing fuel filler hose (1) at the fuel filler tube, mark components for alignment.
11. Remove vent hose (1) and EVAP hose (2) at rear of fuel tank.
- Disconnect vent hose and EVAP hose quick connectors using the following procedures.
a. Pinch retaining tabs (A) of vent hose quick connector and remove vent hose (1).
b. Slide sleeve (B) of EVAP hose quick connector and remove EVAP hose (2).
- If hoses are stuck, push and pull several times until they move freely, and disconnect.
CAUTION:
- The tube can be removed when the tabs are completely depressed. Do not twist it more than necessary.
- Do not use any tools to remove the quick connector.
- Keep the resin tube away from heat. Be especially careful when welding near the tube.
- Prevent acid liquid such as battery electrolyte, from getting on the resin tube.
- Do not bend or twist the tube during installation and removal.
- Do not insert plug that may cause damage to O-ring in quick connector.
- To keep the connecting portion clean and to avoid dam- age and foreign materials, cover them completely with plastic bags or something similar.
12. Support center of fuel tank (1) with transmission jack (A).
CAUTION: Securely support the fuel tank with a suitable tool (B).
13. Remove fuel tank bands (RH and LH).
14. Lower transmission jack carefully to remove fuel tank while supporting it by hand.
CAUTION: Fuel tank may be in an unstable position because of the shape of fuel tank bottom. Be sure to support tank securely.
INSTALLATION
Installation is in the reverse order of removal.
EVAP Canister
1. Check the connection for damage or any foreign materials.
2. Align the connector with the tube, then insert the connector straight into the tube until a "click" sound is heard.
3. After connecting, make sure that the connection is secure.
- Pull the tube and the connector to make sure they are securely connected.
Fuel Tank Bands
Install the fuel tank bands in the proper position by referring to the identification stamp mark "R" and "L" on the end
1. While supporting the fuel tank, install bolts 1, 3 and 4 to support the tank, but do not fully tighten.
2. Install bolt 2 while positioning the fuel tank toward the front of the vehicle. Tighten bolt 2 to specified torque.
3. Tighten bolts 1, 3 and 4 to specified torque.
Fuel Filler Hose
- Insert fuel filler hose to the length below.
Fuel filler install length : 35 mm (1.38 in)
- Be sure hose clamp is not placed on swelled area of fuel filler tube.
EVAP Hose
1. Check connections for damage or foreign material.
2. Align the matching quick connector (A) with the center of EVAP hose (1), and insert quick connector (A) straight until it clicks.
3. After connecting, pull on quick connector (A) and EVAP hose (1) by hand. Make sure connections are secure.
INSPECTION AFTER INSTALLATION
Use the following procedure to check for fuel leaks.
1. Turn ignition switch "ON" (without starting the engine), to check the connections for fuel leaks with the electric fuel pump applying pressure to the fuel piping.
2. Start the engine and let it idle to check that there are no fuel leaks at the fuel system connections.