Inspection After Disassembly

CYLINDER HEAD


Inspection After Disassembly


CYLINDER HEAD DISTORTION





1. Wipe off oil and remove water scale deposits, old gasket, old sealer, and carbon with a scraper.

CAUTION:
Use care not to allow gasket debris to enter passages for oil or water.
2. At each of several locations on bottom surface of cylinder head, measure distortion in six directions.

Limit : 0.1 mm (0.004 in)


VALVE DIMENSIONS
Check dimensions of each valve. Refer to Mechanical Specifications.

VALVE GUIDE CLEARANCE





- Measure diameter of valve stem using suitable tool (A) as shown.






- Measure inner diameter of valve guide with a bore gauge as shown.

Standard Intake and Exhaust : 6.000 - 6.018 mm (0.2362 - 0.2369 in)

- Valve guide clearance = (Valve guide inner diameter) - (Valve stem diameter)






- If it exceeds the limit, replace valve guide and/or valve. When valve guide must be replaced, follow the "VALVE GUIDE REPLACEMENT" procedure.

VALVE GUIDE REPLACEMENT
When valve guide is removed, replace with oversized (0.2 mm, 0.008 in) valve guide.






1. To remove valve guide, heat cylinder head to 110� to 130�C (230� to 266�F) by soaking in heated oil.






2. Drive out valve guide with a press [under a 20 kN (2.2 ton-force) pressure] or hammer and suitable tool.





3. Ream cylinder head valve guide hole using suitable reamer.

Intake and exhaust valve guide hole diameter (Service) : 10.175 - 10.196 mm (0.4006 - 0.4014 in)


4. Heat cylinder head to 110� to 130�C (230� to 266�F) by soaking in heated oil.





5. Press valve guide from camshaft side to dimensions as shown.





6. Apply finish to valve guide using suitable reamer.

Intake and exhaust : 6.000 - 6.018 mm (0.2362 - 0.2369 in)


VALVE SEAT CONTACT

NOTE:





After confirming that the dimensions of valve guides and valves are within specifications, perform this procedure:
- Apply prussian blue (or white lead) onto contacting surface of valve seat to check the condition of the valve contact on the seat surface.
- Check if the contact area band is continuous all around the circumference.
- If not, grind to adjust valve fitting and check again. If the contacting surface still has NG conditions even after the re-check, replace the valve seat.

VALVE SEAT REPLACEMENT

NOTE:
When valve seat is removed, replace with an oversized [0.5 mm (0.020 in)] valve seat.
1. Bore out old seat until it collapses. Boring should not continue beyond the bottom face of the seat recess in the cylinder head. Set the machine depth stop to ensure this.





2. Ream cylinder head recess diameter for service valve seat.






- Be sure to ream in circles concentric to the valve guide center.
This will enable the valve seat to fit correctly.





3. Heat cylinder head to 110� to 130�C (230� to 266�F) by soaking in heated oil.
4. Use valve seats cooled well with dry ice. Force fit valve seat into cylinder head.

CAUTION:
Avoid directly touching the cold valve seats.





5. Finish the seat to the specified dimensions using suitable tool. Refer to Mechanical Specifications.

CAUTION:
When using valve seat cutter, firmly grip the cutter handle with both hands. Then, press on the contacting surface all around the circumference to cut in a single drive. Improper pressure on the cutter or cutting many different times may result in a defective valve seat.
6. Using compound, grind to adjust valve fitting.
7. Check again for normal contact.

VALVE SPRING SQUARENESS





Set try square along the side of the valve spring and rotate the spring. Measure the maximum clearance between the top face of the spring and the try square.

Limit : 1.9 mm (0.0748 in)


VALVE SPRING DIMENSIONS AND VALVE SPRING PRESSURE LOAD





Check valve spring pressure with valve spring seat installed at specified spring height. Replace if not within specifications.

CAUTION:
Do not remove the valve spring seat.