Removal And Installation
FUEL INJECTOR AND FUEL TUBE
Removal and Installation
WARNING:
- Put a "CAUTION: FLAMMABLE" sign in the workshop.
- Be sure to work in a well-ventilated area and furnish workshop with a fire extinguisher.
- Never smoke while servicing fuel system. Keep open flames and sparks away from the work area.
REMOVAL
1.Release the fuel pressure. Testing and Inspection.
2.Remove intake manifold. Removal And Installation.
3.Disconnect fuel feed hose from fuel tube. Disconnect quick connector:
NOTE:
There is no fuel return path.
a.Remove quick connector cap (engine side) (1) from quick connector connection.
b.Disconnect fuel feed hose from hose clamp.
c.With the sleeve (B) side of quick connector release (A) facing quick connector (2), install quick connector release (A) onto fuel tube (1) as shown.
d.Insert quick connector release (A) into quick connector (2) until sleeve (B) contacts and goes no further. Hold quick connector release (A) in that position (D).
CAUTION:
Inserting quick connector release hard will not disconnect quick connector. Hold quick connector release where it contacts and goes no further.
e.Draw and pull out quick connector (E) straight up from fuel tube (1).
CAUTION:
- Pull quick connector up (E) from holding position (C) as shown.
- Never pull with lateral force applied. O-ring inside quick connector may be damaged.
- Prepare container and cloth beforehand as fuel will leak out.
- Discard O-ring, do not reuse.
- Avoid fire and sparks.
- Keep parts away from heat source. Be especially careful when welding is performed.
- Never expose parts to battery electrolyte or other acids.
- Never bend or twist connection between quick connector and fuel feed tube during installation or removal.
- Be sure to cover openings of disconnected fuel feed hose (A) and fuel tube (C) with plug or plastic bag (B) to avoid fuel leaks and entry of foreign material.
4.Disconnect fuel feed hose from fuel pipe as follows:
NOTE:
There is no fuel return path.
a.Remove quick connector cap (floor piping side) (1) from quick connector connection.
b.Disconnect fuel feed hose from hose clamp (1).
c.Hold the quick connector (1) while pushing in tabs (F), and pull out the hard tube (A).
CAUTION:
- Inserting quick connector release hard will not disconnect quick connector. Hold quick connector release where it contacts and goes no further.
- The tube can be removed when the tabs are completely depressed. Do not twist it more than necessary.
- Do not use any tools to remove the quick connector.
- Keep the resin tube away from heat. Be especially careful when welding near the tube.
- Prevent acid such as battery electrolyte etc. from getting on the resin tube.
- Do not bend or twist the tube during installation and removal.
- Remove the remaining retainer only when the tube is replaced.
- When the tube is replaced, also replace the retainer.
- Be sure to cover openings of disconnected pipes with plug or plastic bag (B) to avoid fuel leaks and entry of foreign material.
5.Disconnect harness connector from fuel injector.
6.Remove fuel tube protector.
- Loosen mounting bolts in reverse order as shown.
7.Remove fuel injector and fuel tube assembly:
a.Loosen two nuts in reverse order as shown in the figure.
b.Pull the fuel tube straight out until injector lower O-rings are clear.
c.Remove the nuts and the fuel tube.
CAUTION:
- When removing, be careful to avoid interference with fuel injectors.
- Use a shop cloth to absorb any fuel leaks from fuel tube.
8.Remove fuel injector from fuel tube:
a.Open and remove clip (1).
b.Remove fuel injectors (3) and (4) from fuel tube (2) by pulling straight out.
CAUTION:
- Be careful with remaining fuel that may leak from fuel tube.
- Be careful not to damage fuel injector nozzle during removal.
- Never bump or drop fuel injector.
- Never disassemble fuel injector.
- Do not reuse O-rings.
INSTALLATION
CAUTION:
Do not reuse O-rings.
1.Note the following, and install new O-rings on the fuel injector.
CAUTION:
- Upper and lower O-rings are different. Be careful not to interchange them.
Fuel tube side: Black
Nozzle side: Green
- Handle O-ring with bare hands. Never wear gloves.
- Lubricate O-ring with new engine oil.
- Never clean O-ring with solvent.
- Check that O-ring and its mating part are free of foreign material.
- When installing O-ring, be careful not to scratch it.
- Do not twist or stretch O-ring. If O-ring was stretched while it was being attached, allow it to retract before inserting it into fuel tube.
- Insert O-ring straight into fuel tube. Never angle or twist it.
2.Install fuel injector (4) to fuel tube (1):
a.Insert new clip (2) into clip mounting groove (G) on fuel injector (4).
- Insert new clip (2) so that protrusion (F) of fuel injector matches cut-out (D) of clip.
CAUTION:
- Never reuse clip. Replace it with a new one.
- Be careful to keep clip from interfering with O-ring. If interference occurs, replace O-ring.
b.Insert fuel injector (4) into fuel tube (1) with clip (2) attached.
- Insert fuel injector (4) while matching it to the axial center.
- Insert fuel injector (4) so that protrusion (B) of fuel tube matches cut-out (C) of clip (2).
- Check that fuel tube flange (A) is securely located in flange groove (E) on clip (2).
c.Check that installation is complete by checking that fuel injector (4) does not rotate or come off.
3.Set fuel tube and fuel injector assembly in position for installation on cylinder head.
CAUTION:
For installation, be careful not to interfere with fuel injector nozzle.
- Tighten mounting bolts in numerical order as shown.
4.Install fuel tube protector.
- Tighten mounting bolts in numerical order as shown.
5.Connect harness connector to fuel injector.
6.Connect fuel feed tube (engine side):
a.Check for damage or foreign material on the fuel tube and quick connector.
b.Apply new engine oil lightly to area around the top of fuel tube.
c.Align center to insert quick connector straight into fuel tube.
- Insert quick connector (1) to fuel tube until the top spool (C) on fuel tube is inserted completely and the 2nd level spool (D) is positioned slightly below quick connector bottom end.
CAUTION:
- Hold in position (A) as shown when inserting fuel tube into quick connector.
- Carefully align center to avoid inclined insertion to prevent damage to O-ring inside quick connector.
- Insert until you hear a "click" sound and actually feel the engagement.
d.To avoid misidentification of engagement with a similar sound, pull quick connector hard by hand. Check it is completely engaged (connected) so that it does not come out from fuel tube.
e.Install quick connector cap (engine side) (1) to quick connector connection.
- Install quick connector cap (engine side) (1) with the side arrow facing quick connector side (fuel feed tube side) as shown.
CAUTION:
- Check that the quick connector and fuel tube are securely engaged with the quick connector cap (engine side) mounting groove.
- If the quick connector cap (engine side) cannot be installed easily the quick connector may not be connected correctly. Remove and reconnect.
f.Install fuel feed hose to hose clamp.
7.Connect fuel feed tube (floor piping side):
a.Check the connection for damage or any foreign materials.
b.Align the quick connector with the tube, then insert the connector straight into the centralized under floor piping until a click is heard.
c.After connecting, check that the connection is secure:
- Visually confirm that the two retainer tabs are connected to the connector.
- With the fuel feed hose not fixed to the clamp, pull quick connector (A) hard by hand to check that the quick connector (A)
is not disconnected from the centralized underfloor piping (1)
and that the quick connector (1) is securely connected.
8.Install remaining parts in the reverse order of removal.
INSPECTION AFTER INSTALLATION
Check on Fuel Leaks
1.Turn ignition switch ON with the engine stopped. Ensure there are no fuel leaks at fuel pipe connection points.
NOTE:
Use mirrors for checking points out of clear sight.
2.Start the engine and increase engine speed. Check again that there are no fuel leaks.
CAUTION:
Never touch the engine immediately after stopped, as the engine becomes extremely hot.