Programming and Relearning

CONFIGURATION [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)]

Work Procedure


CAUTION:
- Use "Manual Configuration" only when "TYPE ID" of ABS actuator and electric unit (control unit)
cannot be read.
- After configuration, turn the ignition switch from OFF to ON and check that the VDC warning lamp turns OFF after staying illuminated for approximately two seconds.
- If an error occurs during configuration, start over from the beginning.

1. CHECKING TYPE ID (1)

Use FAST (service parts catalogue) to search ABS actuator and electric unit (control unit) of the applicable vehicle and find "Type ID".
Is "Type ID" displayed?
YES- Print out "Type ID" and GO TO 2.
NO- "Configuration" is not required for ABS actuator and electric unit (control unit). Replace in the usual manner. Refer to "Removal and Installation" Removal And Installation.

2. CHECKING TYPE ID (2)

CONSULT Configuration
1.Select "Before Replace ECU" of "Read/Write Configuration".
2.Check that "Type ID" is displayed on the CONSULT screen.
Is "Type ID" displayed?
YES- GO TO 3.
NO- GO TO 7.

3. VERIFYING TYPE ID (1)

CONSULT Configuration
Compare a "Type ID" displayed on the CONSULT screen with the one searched by using FAST (service parts catalogue) to check that these "Type ID" agree with each other.
NOTE:
For the "Type ID" searched by using FAST (service parts catalog), use the last five digits of the "Type ID".
- GO TO 4.

4. SAVING TYPE ID

CONSULT Configuration
Save "Type ID" on CONSULT.
- GO TO 5.

5. REPLACING ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) (1)

Replace ABS actuator and electric unit (control unit). Refer to "Removal and Installation" Removal And Installation.

CAUTION:
Never perform the following work items:
- Air bleeding
- GO TO 6.

6. WRITING (AUTOMATIC WRITING)

CONSULT Configuration
1.Select "After Replace ECU" of "Re/programming, Configuration" or that of "Read / Write Configuration".
2.Select the "Type ID" agreeing with the one stored on CONSULT and the one searched by using FAST
(service parts catalogue) to write the "Type ID" into the ABS actuator and electric unit (control unit).
NOTE:
For the "Type ID" searched by using FAST (service parts catalog), use the last five digits of the "Type ID".
- GO TO 9.

7. REPLACING ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) (2)

Replace ABS actuator and electric unit (control unit). Refer to "Removal and Installation" Removal And Installation.

CAUTION:
Never perform the following work items:
- Air bleeding
- GO TO 8.

8. WRITING (MANUAL WRITING)

CONSULT Configuration
1.Select "Manual Configuration".
2.Select the "Type ID" searched by using FAST (service parts catalogue) to write the "Type ID" into the ABS
actuator and electric unit (control unit).
NOTE:
For the "Type ID" searched by using FAST (service parts catalog), use the last five digits of the "Type ID".
- GO TO 9.

9. VERIFYING TYPE ID (2)

Compare "Type ID" written into the ABS actuator and electric unit (control unit) with the one searched by using
FAST (service parts catalogue) to check that these "Type ID" agree with each other.
NOTE:
For the "Type ID" searched by using FAST (service parts catalog), use the last five digits of the "Type ID".
- GO TO 10.

10. CHECKING VDC WARNING LAMP

1.Turn the ignition switch OFF.
2.Turn the ignition switch ON and check that the VDC warning lamp turns OFF after staying illuminated for approximately two seconds.

CAUTION:
Never start the engine.
Is the inspection result normal?
YES- GO TO 11.
NO- Perform the self-diagnosis of "ABS". Refer to "CONSULT Function (ABS)" Scan Tool Testing and Procedures.

11. PERFORMING SUPPLEMENTARY WORK

1.Perform the air bleeding. Refer to "Bleeding Brake System" Service and Repair.
2.Perform the self-diagnosis of all systems.
3.Erase self-diagnosis results.
- End of work.