Rear Seat

REAR SEAT

Disassembly and Assembly


SEAT CUSHION











Disassembly
1.Remove the seat cushion assembly. Refer to "Removal and Installation Seat Cushion Assembly" Seat Cushion Assembly.
2.Remove the two clips that retain the seat cushion trim.
3.Release the fastening strips from the seat cushion frame.
4.Remove the seat cushion trim and seat cushion pad from the seat cushion frame.
5.Separate the seat cushion trim from the seat cushion pad.
a.Pull the seat cushion trim upward to release hook fasteners.
b.Remove the six hog rings and separate the seat cushion trim from the seat cushion pad.
NOTE:
Remove all pieces of hog rings and discard them.
Assembly
Assembly is in the reverse order of disassembly.

CAUTION:
- Make sure hog rings are correctly fastened around both the seat cushion trim and seat cushion pad wires.
- Replace any deformed or damaged hog rings.
- Make sure any old hog ring pieces are removed from seat.
NOTE:





- Install new hog rings on the seat cushion trim in original positions.
- Use only one hog ring in each designated location.





- When installing the seat cushion trim, firmly push down while sliding your hand along the seams as shown (black arrow) to ensure the hook fasteners below the seat cushion trim are fastened properly.

REAR SEATBACK ASSEMBLY RH - WITH REMOVABLE HEADREST

Disassembly
1.Remove the rear seatback assembly RH. Refer to "Removal and Installation Seat Assembly" Seat Assembly.
2.Remove the armrest assembly. Refer to "Removal and Installation Armrest Assembly" Armrest Assembly.





3.Release the J-clip retainer (B) and unzip the seatback trim cover (1).
(A) Zipper





4.Remove the seatback trim and seatback pad (2) from the seatback frame (1).
a.Release the J-clip retainers (A) from the seatback frame (1).
b.Remove two hog rings that retain seatback pad in place.
Broken square indicates : Hog ring

c.Release the headrest holder locks as shown and remove the headrest holders (1) from the seatback frame (2).






CAUTION:
Before removing headrest holder, check its orientation (front/rear and right/left).
d.Remove the seatback trim and seatback pad from the seatback frame.
5.Separate the seatback trim from the seatback pad.





a.Pull seatback trim (1) upward to release hook fasteners (A).
b.Remove three hog rings and separate the seatback trim from the seatback pad.
Broken square indicates : Hog ring

NOTE:
Remove all pieces of hog rings and discard them.
Assembly
Assembly is in the reverse order of disassembly.

CAUTION:
- Make sure hog rings are correctly fastened around both the seatback trim and seatback pad wires.
- Replace any deformed or damaged hog rings.
- Make sure any old hog ring pieces are removed from seat.
NOTE:





- Install new hog rings on the seatback trim in original positions.
- Use only one hog ring in each designated location.





- When installing the seatback trim, firmly push down while sliding your hand along the seams as shown (black circle) to ensure the hook fasteners below the seatback trim are fastened properly.

REAR SEATBACK ASSEMBLY RH - WITHOUT REMOVABLE HEADREST

Disassembly
1.Remove the rear seatback assembly RH. Refer to "Removal and Installation Seat Assembly" Seat Assembly.
2.Remove the armrest assembly. Refer to "Removal and Installation Armrest Assembly" Armrest Assembly.





3.Release the J-clip retainer (B) and unzip the seatback trim cover (1).
(A) Zipper





4.Remove the seatback trim and seatback pad (2) from the seatback frame (1).
a.Release the J-clip retainers (A).
b.Remove two hog rings that retain seatback pad in place.
Broken square indicates : Hog ring

c.Remove the seatback trim and seatback pad from the seatback frame.
5.Separate the seatback trim from the seatback pad.





a.Pull seatback trim (1) upward to release hook fasteners (A).
b.Remove three hog rings and separate the seatback trim from the seatback pad.
Broken square indicates : Hog ring

NOTE:
Remove all pieces of hog rings and discard them.
Assembly
Assembly is in the reverse order of disassembly.

CAUTION:
- Make sure hog rings are correctly fastened around both the seatback trim and seatback pad wires.
- Replace any deformed or damaged hog rings.
- Make sure any old hog ring pieces are removed from seat.
NOTE:





- Install new hog rings on the seatback trim in original positions.
- Use only one hog ring in each designated location.





- When installing the seatback trim, firmly push down while sliding your hand along the seams as shown (black circle) to ensure the hook fasteners below the seatback trim are fastened properly.

REAR SEATBACK ASSEMBLY LH - WITH REMOVABLE HEADREST

Disassembly
1.Remove the rear seatback assembly LH. Refer to "Removal and Installation Seat Assembly" Seat Assembly.





2.Release the J-clip retainer (B) and unzip the seatback trim cover (1).
(A) Zipper





3.Remove the seatback trim and seatback pad (2) from the seatback frame (1).
a.Release the J-clip retainer (A).





b.Release the headrest holder locks as shown and remove the headrest holders (1) from the seatback frame (2).

CAUTION:
Before removing headrest holder, check its orientation (front/rear and right/left).
c.Remove the seatback trim and seatback pad from the seatback frame.





4.Separate the seatback trim (1) from the seatback pad.
a.Pull seatback trim upward to release hook fasteners (A).
b.Remove three hog rings and separate the seatback trim from the seatback pad.
Broken square indicates : Hog ring

NOTE:
Remove all pieces of hog rings and discard them.
Assembly
Assembly is in the reverse order of disassembly.

CAUTION:
- Make sure hog rings are correctly fastened around both the seatback trim and seatback pad wires.
- Replace any deformed or damaged hog rings.
- Make sure any old hog ring pieces are removed from seat.
NOTE:





- Install new hog rings on the seatback trim in original positions.
- Use only one hog ring in each designated location.





- When installing the seatback trim, firmly push down while sliding your hand along the seams as shown (black circle) to ensure the hook fasteners below the seatback trim are fastened properly.

REAR SEATBACK ASSEMBLY LH - WITHOUT REMOVABLE HEADREST

Disassembly
1.Remove the rear seatback assembly LH. Refer to "Removal and Installation Seat Assembly" Seat Assembly.





2.Release the J-clip retainer (B) and unzip the seatback trim cover (1).
(A) Zipper





3.Remove the seatback trim and seatback pad (2) from the seatback frame (1).
a.Release the J-clip retainer (A).
b.Remove the seatback trim and seatback pad from the seatback frame.





4.Separate the seatback trim (1) from the seatback pad.
a.Pull seatback trim upward to release hook fasteners (A).
b.Remove three hog rings and separate the seatback trim from the seatback pad.
Broken square indicates : Hog ring

NOTE:
Remove all pieces of hog rings and discard them.
Assembly
Assembly is in the reverse order of disassembly.

CAUTION:
- Make sure hog rings are correctly fastened around both the seatback trim and seatback pad wires.
- Replace any deformed or damaged hog rings.
- Make sure any old hog ring pieces are removed from seat.
NOTE:





- Install new hog rings on the seatback trim in original positions.
- Use only one hog ring in each designated location.





- When installing the seatback trim, firmly push down while sliding your hand along the seams as shown (black circle) to ensure the hook fasteners below the seatback trim are fastened properly.