Service Procedure
NOTE:Before continuing, it is IMPORTANT to make sure:
^ ASIST on the CONSULT PC has been freshly synchronized (updated).
^ All CONSULT related software updates (if any) have been installed.
NOTE:
The CONSULT PC automatically gets all reprogramming software during ASIST synchronization.
^ The Extended Storage Switch is pushed in (customer delivery mode).
Make Sure the newest version of the "Meter Reprogramming Tool" (L50_L33_MeterReprogrammer_V2.0.6.0.exe) has been installed into the CONSULT PC as shown above.
NOTE:
If the newest version of the L50/L33 Re-programmer has already been installed, skip to Meter Reprogramming Procedure.
1. The Panasonic Toughbook (CONSULT PC) automatically gets the L50/L33 Re-programmer tool during ASIST synchronization.
2. The CONSULT PC will display a notification that updates are available.
3. Follow the on-screen instructions to install the L50/L33 Re-programmer tool.
4. Once installed, the L50/L33 Re-programmer tool is available by selecting:
Start > All Programs > L50_L33_MeterReprogrammer_V2.0.6.0.exe
Meter Reprogramming Procedure
1. Connect the plus Vehicle Interface (plus VI) to the vehicle.
^ Make sure to use the correct VI for C-III plus (plus VI).
CAUTION
2. Connect the USB cable between the CONSULT PC and the plus VI.
3. Connect the AC Adapter to the CONSULT PC.
CAUTION
4. Connect a battery charger to the vehicle battery:
^ Set the battery charger at a low charge rate.
NOTE:
The GR-8 (Battery and Electrical Diagnostic Station) set to "Power Supply" mode is recommended.
CAUTION
5. Turn off all external Bluetooth(R) devices (e.g., cell phones, printers, etc.) within range of the CONSULT PC and the VI.
CAUTION
6. Turn the ignition ON with the engine OFF.
7. Turn OFF all vehicle electrical loads such as exterior lights, interior lights, HVAC, blower, rear defogger, audio, NAVI, seat heater, steering wheel heater, etc.
IMPORTANT
8. Turn ON the CONSULT PC.
9. Close all software applications (including ASIST, C-III, or C-III plus):
10. Launch the L50/L33 Reprogramming Tool:
Start > All Programs > L50_L33_MeterReprogrammer_V2.0.6.0.exe
11. When the screen in Figure 1 displays, select METER Re-program.
12. Select OK - meter reprogramming will start.
13. The screen in Figure 3 displays when reprogramming is complete - Select OK.
NOTE:
If the screen in Figure 4 displays, reprogramming is not needed for this vehicle or it has already been done:
a. Select OK.
b. Close the reprogramming tool/software.
c. Skip to step 16.
NOTE:
If the screen in Figure 5 displays:
Try reprogramming at least 3 more times.
a. Select OK and close the reprogramming tool/software.
b. Restart this Service Procedure from the beginning.
^ Make sure all steps are completed correctly.
^ CONSULT software and all other applications are closed.
^ Plus VI is securely connected to the vehicle and USB cable is connected.
^ Battery charger is connected to the vehicle.
IMPORTANT:
If you get the screen in Figure 5 above:
^ Make sure to complete all reprogramming attempts on the current vehicle before moving to another vehicle.
^ Using the reprogramming tool on another vehicle will erase all data for the current vehicle, and the meter for the current vehicle will not be reprogrammable (recoverable).
14. For warranty documentation, print a copy of the screen in Figure 6 and attach it to the repair order.
^ To print, use your browser menu - File => Print => OK.
15. After printing, close the L50/L33 Re-programmer tool/software by selecting the red "X" in upper right corner.
NOTE:
The L50/L33 Re-programmer tool/software must be closed before opening CONSULT III plus.
16. Open CONSULT III plus and erase DTCs from all systems.
NOTE:
The L50/L33 Re-programmer tool/software must be closed before opening CONSULT III plus.
19. Disconnect the battery charger.