Transfer Case Assemble

Transfer Case Assemble

Tools Required

* J 4972-4 Output Shaft Needle Bearing Installer
* J 8092 Driver Handle
* J-08614-A Pinion Flange Holder
* J 44809 Output Shaft Seal Installer
* J 44871 Hub Seal Installer
* J 44872 Pinion Shaft Seal Installer
* J-44873-2 Shoulder Bolts
* J 44875 Right Bearing Race Installer




1. Install the NEW collapsible spacer (2) onto the pinion shaft (3).
2. Install the pinion shaft (3) into the housing.
3. Install the bearing (1) onto the pinion shaft.




4. Install the slinger washer (2) and the new pinion seal (1) to the housing.




5. Using J 44872, install the new pinion seal.





Important: Use a NEW pinion nut.

6. Using a NEW pinion nut (1), install the pinion flange (2) to the pinion shaft.




7. Install J-08614-A (2) and J-44873-2 (1) in order to hold the pinion flange while tightening the nut.
8. Tighten the pinion flange nut until it is snug.

Notice: Refer to Fastener Notice.

9. Tighten the nut slowly in order to crush the collapsible spacer.

Tighten the nut to achieve a rotating torque of 0.9-1.5 N.m (8-14 lb in).

10. Remove J-08614-A (2) and J-44873-2 (1).




11. Using J 4972-4 (2) and J 8092 (1), install the axle shaft bearing (3) to the carrier until the bearing seats.





Notice: Do not install the seal from inside the housing. The outside diameter of the bearing cup may cause seal damage.

12. Using the J 44871 (2) and the J 8092 (1), install the oil seal (3) to the housing.





Notice: The bearing cup must be removed in order to install the seal. If the bearing cup is not removed first, seal damage may occur.

13. Using the J 44871 (2) and the J 8092 (3), install the inner oil seal (1) into the cover.




14. Install the shim (2) and bearing cup (3) into the side cover (1).





Notice: Do not heat the cover to install the cup. Heating the cover will damage the seal.

15. Using the J 44875 (2) and the J 8092 (1), install the cup and the shim.




16. Using the J 44809, install the axle shaft oil seal (2) to the side cover (1).





Important: Grease the seal lips to protect the seal and to ease in assembly.

17. Install the carrier assembly (1) to the housing.





Important: Do not apply excess sealer. Excess sealer could cause premature failure.

18. Apply a 2-3 mm (0.08-0.12 in) amount of sealer GM P/N 1052943 (Canadian P/N 10953491), or equivalent, to the housing (1).





Important:
* Grease the seal lips to protect the seal and to ease in assembly.

* Coat the bolt threads with sealant GM P/N 12345382 (Canadian P/N 10953489).

Install the side cover (1) and bolts (2 and 3) to the housing.
There is not a specific tightening sequence, but the bolts with dowel pins should be tightened first, and alternate the others from side to side.

Tighten the side cover bolts to 37 N.m (27 lb ft).




19. Apply sealant GM P/N 12346004 (Canadian P/N 10953480), or equivalent, to the threads of the drain plug.
20. Install the drain plug (1) into the housing.

Tighten the drain plug to 24 N.m (18 lb ft).




21. Fill the transfer case with 500 ml (17 oz) gear oil GM P/N 12378514 (Canadian P/N 88901045), or equivalent, or until the lube is to the bottom of the lube fill hole.
22. Apply adhesive GM P/N 12345493 (Canadian P/N 10953488), or equivalent, to the threads of the fill plug (1).
23. Install the fill plug (1) to the side cover.

Tighten the fill plug to 15 N.m (11 lb ft).