Neutral - Engine Running
Neutral - Engine Running
When the gear selector lever is moved to the NEUTRAL (N) position, the hydraulic and electrical system operation is identical to PARK (P) range. However, if NEUTRAL is selected after the vehicle was operating in REVERSE (R), the following changes would occur in the hydraulic system.
LOW AND REVERSE CLUTCH RELEASES
Manual Valve
The manual valve is moved to the NEUTRAL position and blocks line (2) pressure from entering the reverse (22) fluid circuit. The reverse (22) fluid circuit is opened to an exhaust at the manual valve.
Low and Reverse Clutch (B3) Assembly
Low and reverse clutch (24) fluid exhausts from the low and reverse clutch assembly allowing the low and reverse clutch to release.
M1 Shift Valve
Exhausting low and reverse clutch (24) fluid is routed into the reverse clutch (23) circuit at the M1 shift valve, the reverse (22) circuit at the #7 accumulator check valve assembly, and on to the manual valve where it exhausts.
Primary Pressure Regulator Valve
Reverse (22) fluid pressure also exhausts from the primary regulator valve plunger, allowing line (2) pressure to return to the normal operating range as in PARK, NEUTRAL and DRIVE gear ranges.
DIRECT CLUTCH (C2) ASSEMBLY RELEASES
Reverse Shift Solenoid (SS) Valve Assembly (S5)
The reverse SS valve assembly is de-energized, causing fluid pressure to build-up in the S5 signal (18) fluid circuit.
Shift Pressure Relay Valve
S5 signal (18) fluid is routed to the shift pressure relay valve and applies the valve against spring force.
Direct Clutch (C2) Assembly
Direct clutch (29) fluid exhausts from direct clutch assembly to the M2 shift valve allowing the direct clutch assembly to release.
M2 Shift Valve
Exhausting direct clutch (29) fluid passes through the M2 shift valve into the direct clutch feed 2 (28) fluid circuit and on to the M1 shift valve.
M1 Shift Valve
At the M1 shift valve exhausting direct clutch fluid passes from the direct clutch feed 2 (28) fluid circuit into the direct clutch feed 1 (27) fluid circuit and continues on to the shift pressure relay valve.
Shift Pressure Relay Valve
Exhausting direct clutch feed 1 (27) fluid passes through the shift pressure relay valve and enters the regulated drive or reverse (21) circuit.
Shift Pressure Control Valve
Exhausting regulated drive or reverse (21) fluid passes through the shift pressure control valve and enters the drive or reverse (20) circuit.
#6 Reverse Shift Ball Check Valve
Exhausting drive or reverse (20) fluid seats the reverse shift ball check valve against the drive (19) fluid passage, enters the reverse (22) fluid passage and continues on to an exhaust at the manual valve.
1-2, 2-3, Reverse Shift Solenoid (SS) Valve Assembly (S3)
The 1-2, 2-3, reverse SS valve assembly is de-energized. However, because there is no fluid supplied to the circuit, the 1-2, 2-3, reverse SS valve assembly has no effect in NEUTRAL.
PASSAGES
1. SUCTION
2. LINE
3. CONVERTER FEED
4. RELEASE
5. APPLY
6. EXHAUST ENABLE
7. COOLER
8. LUBE
9. SOLENOID MODULATOR
10. THROTTLE SIGNAL (SLT)
11. SHIFT CONTROL (SLS)
12. LOCK UP CONTROL (SLU)
13. TCC SIGNAL
14. S1 SIGNAL
15. S2 SIGNAL
16. S3 SIGNAL
17. S4 SIGNAL
18. S5 SIGNAL
19. DRIVE
20. DRIVE OR REVERSE
21. REGULATED DRIVE OR REVERSE
22. REVERSE
23. REVERSE CLUTCH
24. LOW AND REVERSE CLUTCH
25. REVERSE CONTROL
26. FORWARD CLUTCH
27. DIRECT CLUTCH FEED 1
28. DIRECT CLUTCH FEED 2
29. DIRECT CLUTCH
30. B2 CONTROL 1
31. B2 CONTROL 2
32. SECOND CLUTCH
33. B1 CONTROL 1
34. B1 CONTROL 2
35. B1 CONTROL 3
36. SECOND COAST CLUTCH
37. B5 CONTROL 1
38. B5 CONTROL 2
39. 1-2 REVERSE (B5) CLUTCH
40. 4-5 CLUTCH
41. B4 CONTROL
42. B4 RELEASE
43. SERVO RELEASE
44. SERVO FEED
45. SERVO APPLY
46. 3RD GEAR BAND APPLY
47. PN12345
48. PRN15
49. 234NCON
50. 345 ENABLE
51. 45 ENABLE
52. REVERSE INHIBIT
53. VENT
54. EXHAUST
55. SUMP
56. VOID
57. TORQUE CONVERTER SEAL DRAINBACK
Neutral - Engine Running
Neutral - Engine Running:
