P1133

Diagnostic Chart:

Wiring Diagram:

CIRCUIT DESCRIPTION

The PCM continuously monitors the Oxygen Sensor 1 (O2S 1) activity for 100 seconds. During the monitor period, the PCM counts the number of times that the O2S 1 switches from rich to lean and from lean to rich. With this information, a total for all switches can be determined. If the number of switches is too low, a DTC P1133 will be set.

CONDITIONS FOR SETTING THE DTC

^ DTCs P0106, P0107, P0112, P0113, P0117, P0118, P0121, P0122, P0123, P0200, P0300, P0301, P0302, P0303, P0304, P0506, P0507, P1406, P1441 not set.

^ The number of rich to lean counts is less than 30 or the lean to rich counts is less than 40 (auto trans).

^ The number of rich to lean counts is less than 10 or the lean to rich counts is less than 15 (manual trans).

^ Engine speed is between 1600 RPM and 2600 RPM.

^ Throttle Position (TP) angle is between5S % and 20 %.

^ Evaporative emissions control system is commanded open for greater than 36 % Pulse Width Modulation (PWM) (auto trans).

^ Evaporative emissions control system is commanded open for greater than 50 % PWM (manual trans).

^ Purge learned memory is greater than 128 (auto trans).

^ Purge learned memory is greater than 191 (manual trans).

ACTION TAKEN WHEN THE DTC SETS

^ The Malfunction Indicator Lamp (MIL) will illuminate.

^ The PCM will record operating conditions at the time the diagnostic fails. This information will be stored in the Freeze Frame and Failure Records buffers.

^ A history DTC is stored.

^ Coolant fan turns ON.

^ Vehicle will operate in Open Loop.

CONDITIONS FOR CLEARING THE MIL/DTC

^ The MIL will turn OFF after three consecutive ignition cycles in which the diagnostic runs without a fault.

^ A history DTC will clear after 40 consecutive warm up cycles without a fault.

^ DTC(s) can be cleared by using the scan tool.

DIAGNOSTIC AIDS

DTC P1133 is most likely caused by one of the following:

^ Fuel pressure - The system will go rich if fuel pressure is to high. The PCM can compensate for some increase, however, if it gets too high, a DTC P0132 will be set. Refer to Fuel System Diagnosis. System Diagnosis - Fuel System

^ Leaking injector - A leaking or faulty injector can cause the system to go rich.

^ MAP sensor - An output that causes the PCM to sense a higher than normal manifold pressure (low vacuum) can cause the system to go rich. Disconnecting the MAP sensor will allow the PCM to set a fixed value for the MAP sensor. Substitute a different MAP sensor if the rich condition is gone while the sensor is disconnected.

^ Pressure regulator - Check for a leaking fuel pressure regulator diaphragm by checking for the presence of liquid fuel in the vacuum line to the regulator.

^ TP sensor - An intermittent TP sensor output will cause the system to go rich due to a false indication of the engine accelerating.

^ O2S 1 contamination - Inspect O2S 1 for silicone contamination from fuel or use of improper RTV sealant. The sensor may have a white powdery coating and result in a high but false voltage signal (rich exhaust indication). The PCM will then reduce the amount of fuel delivered to the engine causing a severe surge or driveability problem.

TEST DESCRIPTION

Number(s) below refer to the step number(s) on the Diagnostic Table.

1. The Powertrain OBD System Check prompts the technician to complete some basic checks and store the freeze frame and failure records data on the scan tool if applicable. This creates an electronic copy of the data taken when the fault occurred. The information is then stored in the scan tool for later reference.

16. Replacement PCM's must be reprogrammed. Refer to the latest Techline information for programming procedures.

18. If no faults have been found at this point and no additional DTC's were set, refer to Diagnostic Aids for additional checks and information.