Fastener Tightening Specifications - Engine

FASTENER TIGHTENING SPECIFICATIONS
Balance Shaft Cover Nut And Bolt 13 Nm (115 lb in)
Balance Shaft Driven Sprocket Bolt (Left Hand Thread) 30 + 45° Nm 22 + 45° lb ft)
Balance Shaft To Housing Bolts 8 mm Hex 10 + 40° Nm (89 + 40° lb in)
Balance Shaft Housing Bolts 10 mm Hex 15 + 40° Nm (11 + 40° lb ft)
Balance Shaft To Block Bolts 13 mm Hex 25 + 70° Nm (18 + 70° lb ft)
Balance Shaft To Block Bolts 15 mm Hex 53 Nm (39 lb ft)
Balance Shaft To Block Bolts 18 mm Hex 40 + 60° Nm (30 + 60° lb ft)
Camshaft (Exhaust) Rear Cover 14 Nm (124 lb in)
Camshaft Position Sensor Bolt 10 Nm (89 lb in)
Camshaft Sprocket To The Camshaft Bolt 70 Nm (52 lb ft)
Connecting Rod Nuts 25 + 80° Nm (18 + 80° lb ft)
Coolant Bleeder Valve Fully Driven, seated, Not Stripped
Coolant Outlet To Cylinder Head 26 Nm (19 lb ft)
Coolant Pump To Timing Chain Housing 26 Nm (19 lb ft)
Coolant Pump To Coolant Pump Cover 14 Nm (124 lb in)
Coolant Pump Cover To The Block 26 Nm (19 lb ft)
Crankshaft Balancer To The Crankshaft 175 + 90° Nm (129 + 90° lb ft)
Crankshaft Bearing Cap Bolts 20 + 90° Nm (15 + 90° lb ft)
Crankshaft Position Sensor To Block 9 Nm (80 lb in)
Cylinder Head Bolts Refer To Procedure
Cylinder Head Threaded Plug 26 Nm (19 lb ft)
EGR Pipe To The EGR Adapter 26 Nm (19 lb ft)
Engine Coolant Air Bleed Pipe 14 Nm (124 lb in)
Engine Coolant Air Bleed Pipe Nut 42 Nm (31 lb ft)
Engine Coolant Temperature Sensor To The Coolant Outlet 11 Nm (97 lb in)
Engine Coolant Temperature Gauge Sensor To The Cylinder Head Fully Driven, Seated, Not Stripped
Engine Lift Bracket 96 Nm (68 lb ft)
Engine Mount Bracket Adapter To The Block Bolt Manual Trans 60 + 60° Nm (44 + 60° lb ft)
Engine Mount Bracket Adapter To The Block Bolt Auto Trans 60 + 60° Nm (44 + 60° lb ft)
Engine Mount (Right Hand Side) To The Engine Mount Bracket Bolts 62 Nm (46 lb ft)
Engine Mount (Right Hand Side) To The Body Support Nut 44 Nm (32 lb ft)
Engine Mount (Right Hand Side) To The Body Support Bolt 66 Nm (49 lb ft)
Engine Mount Strut 100 Nm (74 lb ft)
Engine Mount Strut Bracket Front Bolts 66 Nm (49 lb ft)
Engine Mount Strut Bracket Bottom Bolts 130 Nm (96 lb ft)
EVAP Canister Purge Valve Solenoid Bracket Bolt 8 Nm (72 lb in)
Exhaust Manifold Upper Heat Shield To The Manifold Bolts 14 Nm (124 lb in)
Exhaust Manifold To The Cylinder Head Nuts 15 Nm (11 lb ft)
Exhaust Manifold To The Cylinder Head Studs 11 Nm (97 lb in)
Exhaust Manifold Brace To The Exhaust Manifold Bolt 56 Nm (41 lb ft)
Exhaust Manifold Brace To The Oil Pan Nuts 26 Nm (19 lb ft)
Flywheel To Clutch Cover 20 + 45° Nm (15 + 45° lb ft)
Flywheel To The Converter 66 Nm (49 lb ft)
Flywheel To The Crankshaft 30 + 45° Nm (22 + 45° lb ft)
Front Cover To The Timing Chain Housing 12 Nm (106 lb in)
Fuel Pipe Bracket To The Camshaft Housing 15 Nm (11 + 30° lb ft)
Fuel Pipe To The Fuel Rail Nut 30 Nm (22 lb ft)
Fuel Rail To The Camshaft Housing 26 Nm (19 lb ft)
Ignition Coil And Module Assembly To The Camshaft Housings 22 Nm (16 lb ft)
Intake Manifold To The Cylinder Head Bolts/Nuts 24 Nm (18 lb ft)
Intake Manifold To The Cylinder Head Studs 11 Nm (97 lb in)
Knock Sensor 20 Nm (15 lb ft)
Oil Filter Connector To The Block 29 Nm (21 lb ft)
Oil/Air Separator To Block Bolts 24 Nm (18 lb ft)
Oil Dipstick Tube Bolt/Screw 8 Nm (71 lb in)
Oil Filter To The Block 3/4 to one complete turn after gasket contact
Oil Pan Bolts 24 Nm (18 lb ft)
Oil Pan Bolts, Second Set 12 Nm (106 lb in)
Oil Pan Drain Plug 26 Nm (19 lb ft)
Oil Pan Studs 26 Nm (19 lb ft)
Oil Passage Plugs, Block 1/8 X 27 10 Nm (89 lb in)
Oil Passage Plugs, 3/8 X 18 30 Nm (22 lb ft)
Oil Passage Plugs, 1/4 X 18 20 Nm (15 lb ft)
Oil Passage Plug Bolt 30 Nm (22 lb ft)
Oil Pressure Switch 14 Nm (124 lb in)
Oil Pump To The Balance Shaft Housing-Long Bolts 12 Nm (106 lb in)
Oil Pump Cover To The Oil Pump Housing-Short Bolts 10 Nm (89 lb in)
Oxygen Sensor To Exhaust Manifold 42 Nm (31 lb ft)
Power steering Pipe To The Pump Nut 27 Nm (20 lb ft)
Power steering Pump To The Cam Carrier Bolts 26 Nm (19 lb ft)
Rear Crankshaft Seal Housing To Block 12 Nm (106 lb in)
Spark Plugs To The Cylinder Head 18 Nm (13 lb ft)
Starter To The Block Bolt 90 Nm (66 lb ft)
Tensioner To Tensioner Bracket Nut 54 Nm (40 lb ft)
Timing Chain Housing To The Camshaft Housings 26 Nm (19 lb ft)
Timing Chain Housing To The Block Bolts/Studs 29 Nm (21 lb ft)
Timing Chain Housing To Housing And Block 10 Nm (89 lb in)
Throttle Body Tot He Intake Manifold 10 Nm (89 lb in)
Thrust Plate To The Balance Shaft Housing 13 Nm (115 lb in)
Transaxle To Block Bolt 58 Nm (43 lb ft)
Transaxle To Block Nut 66 Nm (49 lb ft)
Transaxle To Block Stud 13 Nm (115 lb ft)