P0133
Schematic:
CIRCUIT DESCRIPTION
The PCM continuously monitors the Heated Oxygen Sensor (HO2S) activity for 120 seconds. During the monitoring period the PCM counts the number of times that the a rich to lean and lean to rich response is indicated and adds the amount of time it took to complete all transitions. With this information, an average time for each transition can be determined If the average response time is too slow, a DTC P0133 will be set. A lean to rich transition is indicated when the HO2S voltage changes from less than 300 mV to greater than 600 mV. A rich to lean transition is indicated when the HO2S voltage changes from more than 600 mV to less than 300 mV. An HO2S that responds too slowly is likely to be malfunctioning and should be replaced.
CONDITIONS FOR RUNNING THE DTC
^ None of the following active DTCs are present:
- Throttle Position (TP) sensor
- Evaporative Emissions (EVAP) system
- Misfire
- Intake Air Temperature (IAT) sensor
- Manifold Absolute Pressure (MAP) sensor
- Fuel trim
- Fuel injector circuit
- EGR pintle position
- Engine Coolant Temperature (ECT) sensor
- Crankshaft Position (CKP) sensor
- Mass Air Flow (MAF) sensor
^ The engine has been running in closed loop fuel control for at least 60 seconds.
^ The engine speed is between 1000 RPM and 3000 RPM.
^ The engine coolant temperature is more than 50°C (122°F).
^ The mass air flow is between 10 g/s and 30 g/s.
CONDITIONS FOR SETTING THE DTC
HO2S 1 lean to rich average transition response time during the sample period was more than 130 milliseconds or rich to lean average transition response time during the sample period was more than 110 milliseconds.
ACTION TAKEN WHEN THE DTC SETS
^ The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run and failed.
^ The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
^ If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.
CONDITIONS FOR CLEARING THE MIL/DTC
^ The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
^ The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
^ The DTC can be cleared by using a scan tool.
DIAGNOSTIC AIDS
Check for the following conditions:
^ Faulty connections at PCM-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and faulty terminal to wire connections. Use a corresponding mating terminal to test for proper terminal tension.
^ Inspect the wiring harness for damage. If the hamess appears to be OK, observe the HO2S 1 display on the scan tool while moving connectors and wiring harnesses related to the sensor. A change in the display will indicate the location of the malfunction. If DTC P0133 cannot be duplicated, Reviewing the Fail Records vehicle mileage since the diagnostic test last failed may help determine how often the condition that caused the DTC to be set occurs. This may assist in diagnosing the condition.
TEST DESCRIPTION
Steps 1 - 5:
Steps 6 - 16:
The numbers below refer to the step numbers on the diagnostic table.
2. When the system is operating correctly the HO2S voltage should toggle to more than and less than the specified values.
5. If the low circuit is shorted to ground the HO2S voltage will be less than 400 mV when the signal circuit is jumped to ground.
6. The specified value is what is measured on a correctly operating system.
7. The specified value is what is measured on a correctly operating system.
14. This vehicle is equipped with a PCM which utilizes an electrically Erasable Programmable Read-only Memory (EEPROM). When the PCM is replaced, the new PCM must be programmed.