P0137
Schematic:
CIRCUIT DESCRIPTION
To control emissions of Hydrocarbons (HC), Carbon Monoxide (CO), and Oxides of Nitrogen (NOx), a three-way catalytic converter is used. The catalyst within the converter promotes a chemical reaction which oxidizes the HC and CO present in the exhaust gas, converting them into harmless water vapor and carbon dioxide. The catalyst also reduces NOx, converting it to nitrogen. The PCM has the ability to monitor this process using the HO2S 1 and the HO2S 2 heated oxygen sensors. The HO2S 1 sensor produces an output signal which indicates the amount of oxygen present in the exhaust gas entering the three-way catalytic converter. The HO2S 2 sensor produces an output signal which indicates the oxygen storage capacity of the catalyst. This in turn indicates the catalyst's ability to convert exhaust gases efficiently. If the catalyst is operating efficiently, the HO2S 1 signal will be far more active than that produced by the HO2S 2 sensor. If the HO2S 2 signal voltage remains excessively low for an extended period of time, DTC P0137 will be set.
CONDITIONS FOR RUNNING THE DTC
^ None of the following active DTCs are present:
- Throttle Position (TP) sensor
- Evaporative Emissions (EVAP) system
- Misfire
- Intake Air Temperature (IAT) sensor
- Manifold Absolute Pressure (MAP) sensor
- Fuel trim
- Fuel injector circuit
- EGR pintle position
- Engine Coolant Temperature (ECT) sensor
- Crankshaft Position (CKP) sensor
- Mass Air Flow (MAF) sensor
^ The closed loop commanded air/fuel ratio is between 14.5:1 and 14.8:1.
^ The throttle angle is between 3 percent and 40 percent.
CONDITIONS FOR SETTING THE DTC
^ The HO2S 2 signal voltage remains less than 10 mV during normal closed loop operation.
OR
^ The HO2S 2 signal voltage remains less than 600 mV during power enrichment mode fuel control operation.
^ The condition is present for up to 8 minutes.
ACTION TAKEN WHEN THE DTC SETS
^ The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run and failed.
^ The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
^ If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.
CONDITIONS FOR CLEARING THE MIL/DTC
^ The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
^ The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
^ The DTC can be cleared by using a scan tool.
DIAGNOSTIC AIDS
Check for the following conditions:
^ The heated oxygen sensor pigtail may be mispositioned and contacting the exhaust system.
^ A condition which causes a lean exhaust can cause DTC P0137 to set. The system will go lean if pressure is too low. The PCM can compensate for some decrease. However, if fuel pressure is too low, a DTC P0137 may be set.
^ Correct fuel injector operation
Refer to Fuel Injector Coil Test - Engine Coolant Temperature (ECT) Between 10-35 Degrees C (50-95 Degrees F) or Fuel Injector Coil Test - Engine Coolant Temperature (ECT) Outside 10-35 Degrees C (50-95 Degrees F). Component Tests and General Diagnostics Component Tests and General Diagnostics
^ Check for the following vacuum leaks conditions:
- Any disconnected or damaged vacuum hoses, refer to Emission Hose Routing Diagram.
- An incorrectly installed or malfunctioning crankcase ventilation valve, refer to Crankcase Ventilation System Inspection. Positive Crankcase Ventilation
- Any vacuum leaks at the throttle body, the EGR valve, and the intake manifold mounting surfaces
^ An exhaust leak may cause outside air to be pulled into the exhaust gas stream past the HO2S, causing DTC P0137 to set. Check for exhaust leaks near the HO2S 2 sensor.
^ Check the throttle body inlet screen for damage or objects that may alter the airflow sample through the MAF sensor. If a problem is found, correct as necessary. Refer to Throttle Body Service.
^ Disconnect the MAF sensor. If the lean condition is corrected with the MAF sensor disconnected, replace MAF sensor. Refer to MAF Sensor Replacement.
^ Fuel contamination
Water, even in small amounts, can be delivered to the fuel injectors. The water can cause a lean exhaust to be indicated. Excessive alcohol in the fuel can also cause this condition. Refer to Alcohol/ Contaminants-in-Fuel Diagnosis. Component Tests and General Diagnostics
TEST DESCRIPTION
Diagnostic Chart:
The numbers below refer to the step numbers on the diagnostic table.
3. DTC P0137 failing during power enrichment operation (TP angle more than 60 percent) may indicate a condition described in Diagnostic Aids. If the DTC P0137 test passes while the Fail Records conditions are being duplicated, an intermittent condition is indicated. Reviewing the Fail Records vehicle mileage since the diagnostic test last failed may help determine how often the condition that caused the DTC to be set occurs. This may assist in diagnosing the condition.
6. This vehicle is equipped with a PCM which utilizes an electrically Erasable Programmable Read-only Memory (EEPROM). When the PCM is replaced, the new PCM must be programmed.