P0134

Diagnostic Chart 1 Of 2:

Diagnostic Chart 2 Of 2:

Schematic:

CIRCUIT DESCRIPTION
The Heated Oxygen Sensor (HO2S) produces a voltage that varies between 100 mV and 900 mV. The Powertrain Control Module (PCM) monitors this voltage and determines by the exhaust gas oxygen content whether the air/fuel mixture is rich or lean. When the voltage input at the PCM is about 100 mV the HO2S is indicating a lean air/fuel mixture. When the voltage input is about 900 mV the HO2S is indicating rich air/fuel mixture. The PCM constantly monitors the HO2S signal during closed loop operation and compensates for the rich or the lean condition by decreasing or increasing fuel injector pulse width. A DTC P0134 will be set if the HO2S 1 voltage remains outside the active voltage range for an extended period of time.

CONDITIONS FOR RUNNING THE DTC
^ Barometric pressure is greater than 75 kPa.
^ Engine coolant temperature is greater than 80°C (176°F).
^ Intake air temperature is between 10°C to 70°C (14°F to 158°F).
^ Vehicle speed is above 50 km/h (30 mph) for 2 minutes and then idled for 2 minutes.

CONDITION FOR RUNNING THE DTC
^ The engine is running.
^ The engine is operating in Close Loop.
^ Vehicle speed is above 32 km/h (20 mph).

CONDITIONS FOR SETTING THE DTC
HO2S voltage remains at or below 300 mV for at least 10 seconds.
OR
HO2S voltage remains at or higher than 600 mV for at least 10 seconds.

ACTION TAKEN WHEN THE DTC SETS
^ The PCM illuminates the Malfunction Indicator Lamp (MIL) after two consecutive ignition cycles in which the diagnostic runs with the fault active.
^ The PCM records the operating conditions at the time the diagnostic fails. This information is stored in the Freeze Frame buffer.

CONDITIONS FOR CLEARING THE MIL/DTC
^ The MIL turns OFF after three consecutively passing trips without a fault present.
^ A History DTC clears after 40 consecutive warm-up cycles without a fault.
^ Use the scan tool Clear DTC Information function or disconnect the PCM battery feed in order to clear the DTC.

DIAGNOSTIC AIDS
A DTC P0134 is more likely to set during city driving. Avoid operating the vehicle on the highway when validating a DTC P0134.

Clear the DTCs. Road test the vehicle while monitoring the HO2S test in the MIL/System Status selection under System Information on the scan tool. When the HO2S test indicates complete with a YES status, check for a DTC P0134 under Last Test Failed. If there is no DTC P0134 indicated, the DTC is intermittent and the HO2S system diagnostic is indicating OK at this time.

Check for any of the following conditions:
^ Check for good PCM to engine electrical grounds.
^ A faulty heated oxygen sensor (HO2S) - An HO2S that has a faulty internal ground circuit or an open in the signal circuit will be inactive.
^ A contaminated HO2S - Silicon contamination of the HO2S can cause a sluggish signal voltage to be indicated. Silicon contamination is indicated by a powdery white deposit on the portion of the HO2S exposed to the exhaust stream. Before replacing the HO2S determine and correct the cause of the contamination.
^ A HO2S that becomes coated with soot or other combustion materials may not become active and may set a DTC P0134. Visually inspect the HO2S for this type of contamination. After repairing the cause of the contamination, the HO2S may be cleaned by running a fully warmed-up engine at 1,800-2,200 RPM for 2 to 3 minutes.
^ A faulty electrical connection to the PCM

An intermittent malfunction may be caused by a fault in the HO2S 1 sensor electrical circuit. Inspect the wiring harness and components for any of the following conditions:
^ Backed out terminals
^ Improper mating of terminals
^ Broken electrical connector locks
^ Improperly formed or damaged terminals
^ Faulty terminal to wire connections
^ Physical damage to the wiring harness
^ A broken wire inside the insulation
^ Corrosion of electrical connections, splices, or terminals

If a DTC P0134 cannot be duplicated, the information included in the Freeze Frame data can be useful in determining vehicle operating conditions when the DTC was first set.

TEST DESCRIPTION
The numbers below refer to the step numbers in the Diagnostic Table.
1. The Powertrain OBD system check requires the technician to complete some basic checks and to store the freeze frame data on the scan tool. This creates an electronic copy of the data when the fault occurred. The information is stored in the scan tool for later reference.
3. This step determines if the fault is present at operating temperature.
4. This step checks if the DTC P0134 is still present. Drive the vehicle to verify if the fault is present. Monitor the DTC P0134 diagnostic on the scan tool. If the HO2S test displays a YES status, check for a DTC P0134 on the scan tool. If DTC P0134 does not display, the HO2S system diagnostic has run and passed, indicating that malfunction was not present this time. Clear the DTCs in order to view the current status of the system. The System Status tests only indicate that the test has run. The procedure does not indicate if the test passed or failed. Check the Last Test Failed for related DTCs in order to determine the result of the diagnostic test.
5. This step checks for a voltage on the HO2S signal circuit. If the oxygen sensor is disconnected, the scan tool displays 35 mV or less.
6. This step checks for an open in the HO2S 1 ground circuit.
7. This step checks for an open or for a short in the HO2S 1 signal circuit.
10. A possible cause of a voltage short to the HO2S signal circuit is water. Check the wiring harness and the PCM connectors for water. The water can short the ignition positive voltage to ground.