Operation CHARM: Car repair manuals for everyone.

P0132

Diagnostic Chart:




Schematic:




CIRCUIT DESCRIPTION
The Powertrain Control Module (PCM) supplies a bias voltage of approximately 450 mV between the HO2S signal and low circuits. When measured with a 10 megaohm DMM, this may display as low as 320 mV. The oxygen sensor varies the voltage within a range of approximately 1000 mV when the exhaust is rich, to approximately 10 mV when exhaust is lean. The PCM constantly monitors the HO2S signal during Closed Loop operation and compensates for a rich or lean condition by decreasing or increasing the injector pulse width as necessary. If the HO2S 1 voltage remains excessively high for an extended period of time, DTC P0132 will be set.

CONDITIONS FOR RUNNING THE DTC
^ No active TP, MAP, MAF, ECT, IAT, Air Sensor, Fuel Injector Circuit, or EVAP DTCs are present.
^ The system Voltage is between 9.0-18.0 volts.
^ The Closed Loop commanded air-to-fuel ratio is between 13.0-15.0.
^ The throttle angle is between 5-40 percent.

CONDITIONS FOR SETTING THE DTC
^ HO2S 1 signal voltage remains above 975 mV for more than 50 seconds during normal Closed Loop operation.
OR
^ HO2S 1 signal voltage remains above 200 mV for more than 29 seconds during Deceleration Fuel mode operation.

ACTION TAKEN WHEN THE DTC SETS
^ The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run and failed.
^ The PCM will store the conditions which were present when the DTC set as Freeze Frame and Failure Records data.

CONDITIONS FOR CLEARING THE MIL/DTC
^ The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
^ The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
^ The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect the following items:
^ Fuel Pressure - The system will go rich if the fuel pressure is too high. The PCM can compensate for some increase. If the fuel pressure is too high, refer to Fuel System Pressure Test. Fuel System Pressure Test
^ Perform Injector Balance Test - Refer to Fuel Injector Balance Test. Component Tests and General Diagnostics
^ Inspect the EVAP canister for fuel saturation. If the canister is full of fuel, inspect the canister control and hoses.
^ Disconnect the MAF sensor and see if the rich condition is corrected. If it is, replace the MAF sensor.
^ Inspect for a leaking fuel pressure regulator diaphragm by inspecting the vacuum line to the regulator for the presence of fuel.
^ An intermittent TP sensor output will cause the system to go rich due to a false indication of the engine accelerating.
^ Shorted Heated Oxygen Sensor (HO2S) - If the HO2S is internally shorted the HO2S voltage displayed on the scan tool will be more than 1.0 volt. Disconnect the affected HO2S and jumper the HO2S low circuit to ground with the key ON, engine OFF. If the displayed HO2S voltage changes from more than 1000 mV to approximately 450 mV, replace the HO2S. Silicon contamination of the HO2S can also cause a high HO2S voltage to be indicated. This condition is indicated by a powdery white deposit on the portion of the HO2S that is exposed to the exhaust stream. If contamination is noticed, replace the affected HO2S.
^ Open the HO2S signal or low circuit or faulty HO2S - A faulty connection or an open in the HO2S signal or low circuit can cause the DTC to set during Deceleration Fuel mode. An HO2S which is faulty and not allowing a full voltage swing between the rich and lean thresholds can also cause this condition. Operate the vehicle while monitoring the HO2S voltage with a scan tool. If the HO2S voltage is limited within a range between 300 mV-600 mV, test the HO2S signal and the low circuit wiring and the associated terminal connections. If the wiring and connections are OK, replace the HO2S.

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

^ Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to Diagrams.
^ Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the fault. Refer to Diagrams.
^ PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
3. This DTC failing during Deceleration Fuel mode operation, when the vehicle speed is more than 25 mph and the TP angle is less than 3 percent, may indicate a condition described in Diagnostic Aids. If this DTC test passes while the Fail Records conditions are being duplicated, an intermittent condition is indicated. Review the Fail Records vehicle mileage since the diagnostic test last failed. This may help to determine how often the condition that caused the DTC to be set occurs.
7. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM is replaced, the new PCM must be programmed.