Scan Tool Data Definitions
Scan Tool Data DefinitionsData Display/Definitions
The Scan Tool Data Display/Definitions contains a brief description of all the ABS/TCS data parameters. The menus available depend on the number and type of system on the vehicle and are listed below in alphanumeric order.
- ABS DATA
- ABS/TCS DATA 1
- NORMAL MODE
- SYSTEM DATA
ABS Warning Lamp: The scan tool will display On or Off depending on the state of the ABS indicator.
ABS Pump Motor: The scan tool displays On or Off - This parameter indicates the state of the ABS pump motor.
ABS Relay Feedback: The scan tool display On /Off. This is the commanded state of the relay.
Brake Switch Status: The scan tool displays Applied or Released - The scan tool displays the state of the brake switch.
Desired Throttle Position: The scan tool displays % - The scan tool displays in percent the requested throttle opening.
DTC Status: The scan tool will display Yes/No. This will indicate the status of DTCs.
Engine Speed: The scan tool displays 0 - 10200 RPM - This is essentially a digital tachometer display.
LF Inlet Valve Solenoid: The scan tool will display Active or Inactive. The scan tool displays the commanded state of the LF inlet solenoid valve.
LF Outlet Valve Solenoid: The scan tool will display Active or Inactive. The scan tool displays the commanded state of the LF outlet solenoid valve.
Left Front Wheel Speed: The scan tool displays 0 - 255 km/h or (0 - 158 mph). The scan tool displays the actual speed of the left front wheel.
Left Rear Wheel Speed: The scan tool displays 0 - 255 km/h or (0 - 158 mph). The scan tool displays the actual speed of the left rear wheel.
Low Trac: TCS Active: The scan tool displays Off or On. The scan tool displays On if the TCS indicator is currently being commanded ON.
Low Traction Lamp: The scan tool will display On/Off. This will indicate the state of the LOW TRAC Indicator.
LR Inlet Valve Solenoid: The scan tool displays Active or Inactive. The scan tool displays the commanded state of the LR inlet solenoid valve.
LR Outlet Valve Solenoid: The scan tool displays Active or Inactive. The scan tool displays the commanded state of the LR outlet solenoid valve.
Part Number: The scan tool displays the part number of the control module.
Pump Monitor Status: The scan tool display On /Off. This is the commanded state of the pump.
RF Inlet Valve Solenoid: The scan tool displays Active or Inactive. The scan tool displays the commanded state of the RF inlet solenoid valve.
RF Outlet Valve Solenoid: The scan tool displays Active or Inactive. The scan tool displays the commanded state of the RF outlet solenoid valve.
Right Front Wheel Speed: The scan tool displays 0 - 255 km/h or (0 - 158 mph). The scan tool displays the actual speed of the right front wheel.
Right Rear Wheel Speed: The scan tool displays 0 - 255 km/h or 0 - 158 mph - The scan tool displays the actual speed of the rear wheels.
RR Inlet Valve Solenoid: The scan tool displays Active or Inactive. The scan tool displays the commanded state of the RF inlet solenoid valve.
RR Outlet Valve Solenoid: The scan tool displays Active or Inactive. The scan tool displays the commanded state of the RF outlet solenoid valve.
Stop Lamp Switch Status: The scan tool displays Applied or Released - The scan tool displays the state of the stop lamp switch.
System Type: The scan tool displays the system identification number.
TCS Active: The scan tool displays Off or On. The scan tool displays On if the TCS indicator is currently being commanded ON.
TCS Spark Retard Request: The scan tool displays Nm. Request to reduce spark timing, and torque.
TCS Switch State: The scan tool displays On/Off. The scan tool will display the state of the Traction Control Switch.
TCS Warning Lamp: The scan tool will display On or Off depending on the state of the TCS indicator.
Throttle Angle: The scan tool displays % - The scan tool displays in percent of throttle opening.
Throttle Pedal Position: The scan tool displays % -The scan tool displays in percent the throttle opening.
Traction Control Equipped: The scan tool will display Yes/No. This will indicate if the vehicle is equipped with TCS.
Valve Relay State: The scan tool displays On or Off - This parameter indicates the state of the valve relay.