B0015
DTC B0015
DTC DESCRIPTOR
DTC B0015 01
Left Front Seat Belt Pretensioner Deployment Loop Short to Battery
DTC B0015 02
Left Front Seat Belt Pretensioner Deployment Loop Short to Ground
DTC B0015 04
Left Front Seat Belt Pretensioner Deployment Loop Open Circuit
DTC B0015 0D
Left Front Seat Belt Pretensioner Deployment Loop Resistance Above Threshold
DTC B0015 0E
Left Front Seat Belt Pretensioner Deployment Loop Resistance Below Threshold
DIAGNOSTIC FAULT INFORMATION
IMPORTANT: Always perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Testing and Inspection
CIRCUIT/SYSTEM DESCRIPTION
During a side or frontal crash of sufficient force the inflatable restraint sensing and diagnostic module (SDM) will allow current to flow through the deployment loop in order to deploy the seat belt pretensioner - LF. The SDM performs continuous diagnostic tests on the deployment loops to check for proper circuit continuity and for shorts to ground or voltage.
A shorting bar used within the seat belt pretensioner - LF connector which will short together both seat belt pretensioner - LF high and low circuits when the connector is disconnected, this will help to prevent unwanted deployment of the inflator module during servicing.
CONDITIONS FOR RUNNING THE DTC
Ignition voltage is between 9-16 volts.
CONDITIONS FOR SETTING THE DTC
B0015 01
The seat belt pretensioner - LF high and/or low circuit is short to voltage for 120 milliseconds.
B0015 02
The seat belt pretensioner - LF high and/or low circuit is short to ground for 120 milliseconds.
B0015 04
The seat belt pretensioner - LF high and/or low circuit is open for 120 milliseconds.
B0015 0D
The seat belt pretensioner - LF deployment loop resistance is more than 3.9 ohms for 120 milliseconds.
B0015 0E
The seat belt pretensioner - LF deployment loop resistance is less than 1.1 ohms for 120 milliseconds.
ACTION TAKEN WHEN THE DTC SETS
- The SDM commands the AIR BAG indicator ON via serial data communications.
- The SIR system is disabled and no deployments are allowed.
CONDITIONS FOR CLEARING THE DTC
- The condition responsible for setting the DTC no longer exists and the scan tool Clear DTCs function is used.
- A history DTC will clear once 255 malfunction-free ignition cycles have occurred.
CIRCUIT/SYSTEM TESTING
1. Ignition OFF, disconnect the seat belt retractor pretensioner - LF connector located in the center pillar.
IMPORTANT: When removing connectors inspect for damage or corrosion. Damage or corrosion in the following requires repair or replacement of the affected component/connector.
- The seat belt retractor pretensioner - LF
- The SDM module
- The seat belt retractor pretensioner - LF wiring harness connector
- The SDM wiring harness connector
2. Use the J 38715-30A to connect the J 38715-A to the harness side of the seat belt retractor pretensioner - LF connector. Use the PASSENGER INFLATOR connector located on the load tool.
3. Ignition ON, use a scan tool to observe the SIR DTC display. Verify DTC B0015 is set current.
- If DTC B0015 is history replace the seat belt retractor pretensioner - LF.
4. Ignition OFF, disconnect and remove both the J 38715-A and adapter. Then remove the SDM connector.
5. Test the high and low circuits between the SDM and seat belt retractor pretensioner - LF for a short to voltage, short to ground, an open, or low resistance. Verify that a short to voltage, short to ground, or open/low resistance does not exist.
- If any of the above conditions are found make the appropriate repair.
6. If all circuits test normal then replace the SDM.
REPAIR INSTRUCTIONS
IMPORTANT: Always perform the Diagnostic Repair Verification after completing the diagnostic procedure. Verification Tests
- Seat Belt Retractor Pretensioner Replacement - Front (Convertible) Seat Belt Retractor Pretensioner Replacement - Front (Coupe) Seat Belt Retractor Pretensioner Replacement - Front (Sedan)
- Control Module References for SDM replacement, setup, and programming