SIR Disabling and Enabling Zone 8

SIR DISABLING AND ENABLING ZONE 8

DISABLING PROCEDURE
1. Turn the steering wheel so that the vehicles wheels are pointing straight ahead.
2. Turn the ignition switch to the OFF position.
3. Remove the key from the ignition switch.
4. Locate the body control module (BCM) fuse center then remove fuse center cover.




5. Locate and remove the AIR BAG (IGN) and AIR BAG (BATT) fuses from the BCM fuse center.

IMPORTANT: This inflatable restraint sensing and diagnostic module (SDM) has two fused power inputs. To ensure there is no unwanted SIR deployment, personal injury, or unnecessary SIR system repairs, remove both AIR BAG (IGN) and AIR BAG (BATT) fuses from the BCM fuse center. With the AIR BAG fuses removed and the ignition switch in the ON position, the AIR BAG warning indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.





6. Remove the garnish molding from the right upper lock pillar.
7. Remove the connector position assurance (CPA) from the roof rail module-right connector.
8. Disconnect the roof rail module-right connector from the vehicle harness connector.




9. Remove the lower right center pillar trim.
10. Remove the CPA from seat belt pretensioner-RF connector.
11. Disconnect the seat belt pretensioner-RF connector from the vehicle harness connector.




12. Remove the passenger/right outer trim cover from the instrument panel (I/P) (3).
13. Remove the CPA from the I/P module connector (1).
14. Disconnect the I/P module connector (1) from the vehicle harness connector (2).




15. Remove the driver/left outer trim cover from the I/P.
16. Remove the CPA from the steering wheel module coil connector.
17. Disconnect the steering wheel module coil connector from the vehicle harness connector.




18. Remove the lower left center pillar trim.
19. Remove the CPA from seat belt pretensioner-LF connector.
20. Disconnect the seat belt pretensioner-LF connector from the vehicle harness connector.




21. Remove the garnish molding from the left upper lock pillar.
22. Remove the CPA from the roof rail module-left connector.
23. Disconnect the roof rail module-left connector from the vehicle harness connector.

ENABLING PROCEDURE
1. Remove the key from the ignition switch.




2. Connect the roof rail module-left connector to the vehicle harness connector.
3. Install the CPA to the roof rail module-left connector.
4. Install the garnish molding to the left upper lock pillar.




5. Connect the seat belt pretensioner-LF connector.
6. Install the CPA to the seat belt pretensioner-LF connector.
7. Install the left/driver lower center pillar trim.




8. Connect the steering wheel module coil connector to the vehicle harness connector.
9. Install the CPA to the steering wheel module coil connector.
10. Install the driver/left outer trim cover to the I/P.




11. Connect the I/P module connector (1) to the vehicle harness connector (2).
12. Install the CPA to the I/P module connector (1).
13. Install the passenger/right outer trim cover to the I/P (3).




14. Connect the seat belt pretensioner-RF connector.
15. Install the CPA to the seat belt pretensioner-RF connector.
16. Install the right lower center pillar trim.




17. Connect the roof rail module-right connector to the vehicle harness connector.
18. Install the CPA to the roof rail module-right connector.
19. Install the garnish molding to the right upper lock pillar.




20. Install the AIR BAG (IGN) and AIR BAG (BATT) fuses into the BCM fuse center.
21. Install the BCM fuse center cover.
22. Use caution while reaching in and turn the ignition switch to the ON position.The AIR BAG indicator will flash then turn OFF.
23. Perform the Diagnostic System Check - Vehicle if the AIR BAG warning indicator does not operate as described. Refer to Diagnostic System Check - Vehicle. Testing and Inspection