P0112
DTC P0112
DTC DESCRIPTORS
DTC P0112
Intake Air Temperature (IAT) Sensor Circuit Low Voltage
DTC P0113
Intake Air Temperature (IAT) Sensor Circuit High Voltage
DTC P1111
Intake Air Temperature (IAT) Sensor Circuit Intermittent High Voltage
DTC P1112
Intake Air Temperature (IAT) Sensor Circuit Intermittent High Voltage
DIAGNOSTIC FAULT INFORMATION
IMPORTANT: Always perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Testing and Inspection
TYPICAL SCAN TOOL DATA
IAT Sensor Temperature:
CIRCUIT/SYSTEM DESCRIPTION
The intake air temperature (IAT) sensor is a variable resistor. The IAT sensor has a signal circuit and a low reference circuit. The IAT sensor measures the temperature of the air entering the engine. The control module supplies 5 volts to the IAT signal circuit and a ground for the IAT low reference circuit. When the IAT sensor is cold, the sensor resistance is high. When the air temperature increases, the sensor resistance decreases. With high sensor resistance, the control module detects a high voltage on the IAT signal circuit. With lower sensor resistance, the control module detects a lower voltage on the IAT signal circuit. If the control module detects an excessively low IAT signal voltage, indicating a high temperature, DTC P0112 sets. If the control module detects an excessively high IAT signal voltage, indicating a low temperature, DTC P0113 sets. If the control module detects an intermittent high IAT signal voltage, indicating a low temperature, DTC P1111 sets. If the control module detects an intermittent low IAT signal voltage, indicating a high temperature, DTC P1112 sets.
CONDITIONS FOR RUNNING THE DTC
P0112
- DTCs P0116, P0117, P0118, P0125-L32 only, P0128, P0502, P0503 are not set.
- The engine run time is more than 10 seconds.
- The vehicle speed sensor (VSS) indicates that vehicle speed is more than 40 km/h (25 mph).
- The engine coolant temperature (ECT) is less than 121°C (250°F).
- The diagnostic runs continuously when the above conditions are met.
P0113
- DTCs P0101, P0102, P0103, P0116, P0117, P0118, P0125-L32 only, P0128, P0502, P0503 are not set.
- The engine run time is more than 180 seconds.
- The VSS indicates that vehicle speed is less than 24 km/h (15 mph).
- The mass air flow (MAF) is less than 10 g/s.
- The ECT is more than 60°C (140°F).
- The diagnostic runs continuously when the above conditions are met.
P1111
- DTCs P0101, P0102, P0103, P0116, P0117, P0118, P0125-L32 only, P0128, P0502, P0503 are not set.
- The engine run time is more than 180 seconds.
- The ECT sensor parameter is more than 60°C (140°F).
- The vehicle speed is less than 24 km/h (15 mph).
- The MAF is less than 10 g/s.
- The diagnostic runs continuously when the above conditions are met.
P1112
- DTCs P0116, P0117, P0118, P0125-L32 only, P0128, P0502, P0503 are not set.
- The engine run time is more than 10 seconds.
- The ECT sensor parameter is less than 121°C (250°F).
- The VSS indicates that vehicle speed is more than 40 km/h (25 mph).
- The diagnostic runs continuously when the above conditions are met.
CONDITIONS FOR SETTING THE DTC
P0112
The control module detects that the IAT sensor parameter is more than 130°C (266°F) for more than 18 seconds.
P0113
The control module detects that the IAT sensor parameter is less than -36°C (-33°F) for more than 110 seconds.
P1111
The control module detects that the IAT sensor parameter is less than -36°C (-33°F) intermittently for more than 100 seconds.
P1112
The control module detects that the IAT sensor parameter is more than 130°C (266°F) intermittently for more than 16 seconds.
ACTION TAKEN WHEN THE DTC SETS
P0112 and P0113
- The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails.
- The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records.
P1112 and P1111
- The control module stores the DTC information into memory when the diagnostic runs and fails.
- The MIL will not illuminate.
- The control module records the operating conditions at the time the diagnostic fails. The control module stores this information in the Failure Records.
- The driver information center (DIC), if equipped, may display a message.
CONDITIONS FOR CLEARING THE DTC
P0112 or P0113
- The control module turns OFF the MIL after 3 consecutive ignition cycles that the diagnostic runs and does not fail.
- A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
- A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
- Clear the MIL and the DTC with a scan tool.
P1112 or P1111
- A current DTC Last Test Failed clears when the diagnostic runs and passes.
- A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other non-emission related diagnostic.
- Clear the DTC with a scan tool.
DIAGNOSTIC AIDS
When the vehicle is at ambient temperature, the IAT sensor and the ECT sensor should be relatively close to each other. Refer to Temperature vs Resistance.
CIRCUIT/SYSTEM TESTING
Always perform the Diagnostic System Check - Vehicle. Testing and Inspection
P0112 or P1112
1. Observe the IAT sensor with a scan tool for 130°C (266°F).
2. Disconnect the MAF/IAT sensor. Observe the IAT sensor with a scan tool for -36°C (-33°F).
- If more than specified temperature, then test the signal circuit of the IAT sensor for a short to ground or a short to the IAT low reference circuit and repair as necessary. Test for an intermittent and for a poor connection at the control module. If all circuits test OK then replace the control module.
- If less than specified temperature, then test for an intermittent and for a poor connection at the IAT sensor. If circuit tests OK then replace the MAF/IAT sensor.
IMPORTANT: The sensor may be damaged if the circuit is shorted to a voltage source.
P0113 or P1111
1. Turn ON the ignition, with the engine OFF. Disconnect the MAF/IAT sensor. Connect a DMM between the signal circuit of the IAT sensor and a good ground. Measure for 5.2 volts.
- If more than 5.2 volts, then test the signal circuit for a short to voltage.
2. Connect a 3-amp fused jumper wire between the signal circuit of the IAT sensor and the low reference circuit of the IAT sensor. Observe the IAT sensor parameter with a scan tool for 130°C (266°F).
- If more than 130°C (266°F), then test the IAT signal circuit for a short to any 5-volt reference circuit, or for an intermittent and for a poor connection at the IAT sensor. If circuits test OK, then replace the MAF/IAT sensor.
3. Connect a 3-amp fused jumper wire between the signal circuit of the IAT sensor and a good ground. Observe the IAT sensor parameter with a scan tool for 130°C (266°F).
- If more than 130°C (266°F), then test the IAT sensor low reference circuit for high resistance or for an open. Test for an intermittent and for a poor connection at the control module. If circuits test OK, then replace the control module.
REPAIR INSTRUCTIONS
- Mass Air Flow (MAF)/Intake Air Temperature (IAT) Sensor Replacement
- Control Module References for PCM replacement, setup, and programming.
REPAIR VERIFICATION
Diagnostic Repair Verification