P0455

DTC P0455

SYSTEM DESCRIPTION
The DTC P0455 Evaporative Emission (EVAP) System Large Leak Detected diagnostic detects evaporative emission system leaks as small as 1.0 mm (0.040 in). The diagnostic strategy for the EVAP system uses a vacuum pump to test for system leaks after the engine is OFF. A unique fuel tank, EVAP canister, and EVAP vacuum leak pump, work together in order to provide enhanced system diagnosis. The vacuum leak pump, the fuel tank pressure (FTP) sensor and the EVAP canister vent valve are all integral parts of one assembly. The assembly is attached directly to the EVAP canister, located near the fuel tank.

After the vehicle has sat with the engine OFF for about 5 hours, a comprehensive diagnostic is enabled with no operator input necessary. The complete test can take up to 15 minutes to run, with leak detection comprising the largest portion of the test. If a specified minimum value of vacuum pressure is not achieved, a DTC P0455 will set. For more detailed information on the EVAP system components and diagnostic strategy, refer to Evaporative Emission (EVAP) Control System Description.

DTC DESCRIPTOR
This diagnostic procedure supports the following DTC:
DTC P0455 Evaporative Emission (EVAP) System Large Leak Detected

CONDITIONS FOR RUNNING THE DTC
- DTCs P0011, P0012, P0100, P0101, P0102, P0103, P0110, P0112, P0113, P0115, P0117, P0118, P0120, P0121, P0122, P0123, P0125, P0300, P0301-P0304, P0335, P0340, P0341, P0351-P0354, P0385, P043E, P043F, P0441, P0450, P0451, P0452, P0453, P0500, P2401, P2402, P2419, P2420, P2610 are not set.
- Five hours have elapsed after the engine was turned OFF.
- Altitude is less than 2,400 meters (8,000 feet).
- Battery voltage is more than 10.5 volts.
- Engine coolant temperature is between 4-35°C (40-95°F).
- Intake air temperature is between 4-35°C (40-95°F).
- The ignition remains OFF for the duration of the test.
- DTC P0455 runs once per drive cycle when the above conditions are met.

CONDITIONS FOR SETTING THE DTC
The specified minimum value of vacuum pressure was not obtained.

ACTION TAKEN WHEN THE DTC SETS
- The PCM illuminates the malfunction indicator lamp (MIL) after 2 consecutive ignition cycles in which the diagnostic runs with the fault active.
- The PCM records the operating conditions at the time the diagnostic fails. This information is stored in the Freeze Frame buffer.

CONDITIONS FOR CLEARING THE MIL/DTC
- The PCM turns OFF the MIL on the third consecutive trip cycle during which the diagnostic has been run and the fault condition is no longer present.
- A DTC will clear after 40 consecutive warm-up cycles have occurred without a fault.
- A DTC can be cleared by using the scan tool Clear Information function.

DIAGNOSTIC AIDS
- A faulty EVAP canister can cause a DTC P0455 to set. Test the EVAP canister for internal passage leaks and restrictions. Also test the canister for the correct operation of diaphragms, check balls, and internal valves. Refer to Evaporative Emission (EVAP) Control System Diagnosis. Evaporative Emission (EVAP) Control System Diagnosis
- A faulty EVAP canister vent solenoid can cause a DTC P0455 to set. Test the EVAP canister vent solenoid, located in the EVAP vacuum leak pump assembly, for an internal leak. Refer to Evaporative Emission (EVAP) Control System Diagnosis. Evaporative Emission (EVAP) Control System Diagnosis
- To help locate intermittent leaks, use the J 41413-200 Evaporative Emissions System Tester (EEST) to introduce smoke into the EVAP system. Move all EVAP components while observing smoke with the J 41413-SPT High Intensity Lamp.
- A temporary blockage in the EVAP purge solenoid, purge pipe or EVAP canister could cause an intermittent condition. Inspect and repair any restriction in the EVAP system.
- In order to improve the visibility of the smoke exiting the EVAP system, observe the suspected leak area from different angles with the J 41413-SPT.
- Reviewing the Freeze Frame Records vehicle mileage since the diagnostic test last failed may help determine how often the condition that caused the DTC to be set occurs. This may assist in diagnosing the condition.
- For intermittent conditions refer to Intermittent Conditions. Intermittent Conditions

TEST DESCRIPTION

Step 1 - Step 5:

Step 6 - Step 12:

The numbers below refer to the step numbers on the diagnostic table.
2. If there any other EVAP system DTCs set, repair those DTCs first.
5. Waiting until smoke is seen before plugging the EVAP canister vent line speeds up the filling of the canister and fuel tank with smoke. Introducing smoke in between 60 second intervals of Nitrogen also increases the speed of the filling of smoke in the fuel tank, the filler pipe vapor space, and the EVAP canister. This occurs because the pressure at which Nitrogen gas is applied is greater than the pressure at which smoke is introduced. The Nitrogen gas pushes the smoke that was just introduced through the canister and into the fuel tank. The EVAP vent solenoid DOES NOT have to be turned ON in order to test for leaks. The installation of the 41413-324 adapter into the EVAP air filter line seals the tank side of the EVAP system.
7. This test verifies that the FTP sensor is accurate. The FTP sensor should indicate little or no pressure with fuel fill pipe open. An FTP sensor that does not correctly respond to vacuum, or pressure may cause this DTC to set.
8. This step tests the operation of the EVAP vent solenoid located in the EVAP vacuum leak pump assembly. If the vent solenoid passage leaks, or is blocked, the EVAP system leak diagnostic will fail and set a DTC. If the 0.51 mm (0.020 in) reference orifice in the vacuum leak pump assembly is restricted, a DTC can set. These internal leaks and restrictions are not detected using the J 41413-200 EEST, but can set this DTC.
9. This step tests for a blockage or a restriction in the air inlet passage to the EVAP vent solenoid located in the vacuum leak pump assembly. This type of blockage or restriction is not detected using the J 41413-200 EEST, but can set this DTC.
10. This step verifies whether a leak in the EVAP system still exists. If the flow gage on the EEST and/or the scan tool pressure reading remain constant, there is no external leak. If the EEST gage indicates flow, or the scan tool pressure reading decreases, there is still an external leak in the EVAP system.
11. This step uses the EVAP Service Bay test in order to verify the correct operation of the EVAP canister purge solenoid, vent solenoid, and the other EVAP system components. Performing the EVAP Service Bay test also tests for EVAP system leaks. Service Bay Test