Control Valve Lower Body and Upper Body Replacement
Control Valve Lower Body and Upper Body Replacement
Removal Procedure
1. Remove the control valve body cover.
2. Disconnect the input speed sensor electrical connector (1).
3. Disconnect the output speed sensor electrical connector (2).
4. Disconnect the shift position switch electrical connector (3).
5. Remove the control valve body bolts (1) M6 x 80 (Qty: 4).
6. Position the control solenoid valve spring (8) to the side. Spring will be released with removal of lower control valve body.
7. Remove the control valve body bolts (4) M6 x 65 (Qty: 2).
8. Remove the control valve body bolt (3) M6 x 42 (Qty: 1).
9. Remove the control valve body bolts (2) M6 x 95 (Qty: 3).
10. Remove the control valve body bolt (7) M6 x 55 (Qty: 1).
11. Remove the upper control solenoid valve body and TCM assembly (5).
Notice: Use care when removing or installing the filter plate assembly. A broken or missing retaining tab may not adequately secure the filter plate to the control solenoid valve assembly, resulting in possible damage or contamination.
12. Remove the control solenoid valve body assembly filter plate (6).
13. Remove the control valve body bolts (2) M6 x 65 (Qty: 8).
14. Remove the control valve body bolts (1) M6 x 55 (Qty: 2).
15. Remove the manual shaft detent assembly (3).
16. Remove the lower control valve body assembly (4).
17. The control solenoid valve spring can now be fully removed from the lower control valve body assembly.
Important: The clutch fluid passage seal is not reusable.
18. Remove the 1-2-3-4 clutch fluid passage seal (5).
Installation Procedure
Important: The clutch fluid passage seal is not reusable.
1. Install a NEW 1-2-3-4 clutch fluid passage seal (3).
Important: Ensure the control solenoid valve spring is attached to the lower control valve body assembly.
Important: Align the manual valve (2) to the detent lever assembly while installing the lower control valve body assembly.
2. Install the lower control valve body assembly (1).
Important: Ensure proper alignment of the detent assembly to the detent lever assembly with position switch while tightening the bolt. The detent assembly can move and hit the valve body assembly that could cause improper engagement with the detent lever assembly.
3. Install the manual shaft detent assembly (2).
Important: Install all bolts before tightening, then tighten in specified sequence.
Notice: Refer to Fastener Notice.
4. Install the control valve body bolts (1) M6 x 65 (Qty: 8).
Tighten the bolts in specified sequence to 12 N.m (106 lb in).
5. Install the control valve body bolts (3) M6 x 55 (Qty: 2).
Tighten the bolts in specified sequence to 12 N.m (106 lb in).
Notice: Use care when removing or installing the filter plate assembly. A broken or missing retaining tab may not adequately secure the filter plate to the control solenoid valve assembly, resulting in possible damage or contamination.
6. Install the control solenoid valve assembly filter plate (1).
7. Install the control solenoid valve body and TCM assembly (5).
8. Rotate the control solenoid valve spring (7) into position.
Important: Install all bolts before tightening, then tighten in specified sequence.
9. Install the control valve body bolts (1) M6 x 80 (Qty: 4).
10. Install the control valve body bolt (6) M6 x 55 (Qty: 1).
11. Install the control valve body bolts (2) M6 x 95 (Qty: 3).
12. Install the control valve body bolt (3) M6 x 42 (Qty: 1).
13. Install the control valve body bolts (4) M6 x 65 (Qty: 2).
14. Connect the input speed sensor electrical connector (1).
15. Connect the output speed sensor electrical connector (2).
16. Connect the shift position switch electrical connector (3).
17. Install the control valve body cover.
18. For transmission control module programming and setup. Refer to Control Module References.
Important: After an internal transmission repair or internal part replacement the service fast learn adapt procedure should be performed.
19. Perform the service fast learn adapt procedure. Refer to Service Fast Learn Adapts.