P0317
DTC P0317
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (Diagnostic System Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Strategy Based Diagnosis) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Diagnostic Procedure Instructions) provides an overview of each diagnostic category.
DTC Descriptor
DTC P0317
- Rough Road Signal Not Detected
Diagnostic Fault Information
Typical Scan Tool Data
Circuit/System Description
The engine control module (ECM) identifies engine misfire by detecting variations in crankshaft speed. Crankshaft speed variations can also occur when a vehicle is operating over a rough road. The ECM receives a rough road signal by a gravity sensing rough road sensor or an electronic brake control module (EBCM), if equipped with the antilock brake system (ABS). The ABS can detect if the vehicle is on the rough surface based on wheel acceleration/deceleration data supplied by each wheel speed sensor. This information is sent to the ECM by the EBCM through a serial data line. The rough road sensor is a vertical low G-acceleration sensor. By sensing vertical acceleration caused by rough road conditions, the ECM determines if the changes in crankshaft speed are due to engine misfire or are driveline induced. The rough road sensor consist of the following circuits:
* A 5-volt reference
* A rough road sensor signal
* A low reference
Conditions for Running the DTC
* The engine has been running for greater than 10 seconds.
* DTC P0317 runs continuously once the above condition is met for greater than 10 seconds.
Conditions for Setting the DTC
The ECM does not detect a rough road signal for greater than 9 seconds.
Action Taken When the DTC Sets
DTC P0317 is a Type C DTC.
Conditions for Clearing the DTC
DTC P0317 is a Type C DTC.
Diagnostic Aids
* If a shared 5-volt reference circuit is shorted to ground or shorted to a voltage, other 5-volt reference circuits may be affected.
* The scan tool 5 volt reference parameter should display between 4.8-5.2 volts.
Reference Information
Schematic Reference
Engine Controls Schematics ([1][2]Electrical Diagrams)
Electrical Information Reference
* Circuit Testing (Circuit Testing)
* Connector Repairs (Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (Powertrain Diagnostic Trouble Code (DTC) Type Definitions)
Scan Tool Reference
Control Module References (Programming and Relearning) for scan tool information
Circuit/System Verification
1. Ignition ON, observe the DTC information with a scan tool. Verify that DTC P0641 or P0651 is not set.
• If any of the DTCs are set, refer to DTC P0641 or P0651 (P0641).
2. Engine running, observe the DTC information with a scan tool. DTC P0317 should not set.
3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
1. If the vehicle is equipped with ABS, test the circuit between the EBCM and the ECM for an open/high resistance.
• If the circuit tests normal, refer to Symptoms - Antilock Brake System (Symptoms - Antilock Brake System).
2. Ignition OFF, disconnect the harness connector at the rough road sensor.
3. Ignition OFF, test for less than 5 ohms of resistance between the low reference circuit terminal A or C and ground.
• If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM.
Important: The 5-volt reference circuits are internally and externally connected at the ECM. Other component DTCs may be set. If other DTCs are set, review the electrical schematic and diagnose the applicable circuits and components.
4. Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit terminal A or C and ground.
• If less than the specified range, test the 5-volt reference circuit for a short to ground or open/high resistance. If the circuit tests normal, replace the ECM.
• If greater than the specified range, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the ECM.
5. Verify the scan tool rough road sensor voltage parameter is less than 0.1 volt.
• If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the ECM.
6. Install a 3A fused jumper wire between the signal circuit terminal B and the 5-volt reference circuit terminal A or C. Verify the scan tool rough road sensor parameter is greater than 4.8 volts.
• If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the ECM.
7. If all circuits test normal, test or replace the rough road sensor.
Repair Instructions
Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.
* Rough Road Sensor Replacement (Service and Repair)
* Control Module References (Programming and Relearning) for engine control module replacement, setup, and programming