Trunk Release Malfunction
Trunk Release Malfunction
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis Strategy Based Diagnosis for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions Diagnostic Procedure Instructionsprovide an overview of each diagnostic category.
Diagnostic Fault Information
Circuit/System Description
When the ignition is ON, the body control module (BCM) supplies battery positive voltage to the rear compartment lid release switch through the trunk release switch supply voltage circuit. When the rear compartment lid release switch is operated, the trunk release supply voltage circuit is grounded through the switch ground circuit and the voltage is pulled low within the BCM. In response, the BCM applies ground to the trunk release relay control circuit, which energizes the coil side of the relay. The switch side of the relay then closes, supplying battery positive voltage through the relay and the latch motor voltage control circuit to the rear compartment lid latch. The rear compartment lid latch then releases the rear compartment lid so that it may be manually raised to an open position.
Reference Information
Schematic Reference
Release Systems Schematics Release Systems Schematics
Connector End View Reference
Component Connector End Views Connector End Views By Name
Description and Operation
Luggage Compartment Description and Operation (Sedan) Description and Operation
Electrical Information Reference
* Circuit Testing Circuit Testing
* Connector Repairs Connector Repairs
* Testing for Intermittent Conditions and Poor Connections Testing for Intermittent Conditions and Poor Connections
* Wiring Repairs Wiring Repairs
Scan Tool Reference
Control Module References Programming and Relearningfor scan tool information
Circuit/System Verification
1. Ignition ON, observe the scan tool Trunk Release Switch parameter while pressing and releasing the interior rear compartment lid release switch. The parameter should change between Active and Inactive.
• If the parameter does not change, refer to Trunk Release Switch Malfunction.
2. Command the trunk release with a scan tool, the rear compartment lid latch should release the trunk lid.
• If the rear compartment lid latch does not release, refer to Rear Compartment Lid Latch Malfunction.
Circuit/System Testing
Trunk Release Switch Malfunction
1. Ignition OFF, disconnect the harness connector at the appropriate rear compartment lid release switch.
2. Test for less than 15 ohm between the ground circuit terminal A and ground.
• If greater than the specified range, test the ground circuit for an open/high resistance.
3. Ignition ON, verify the scan tool Trunk Release Switch parameter is Inactive.
• If not the specified value, test the signal circuit terminal listed below for a short to ground. If the circuit tests normal, replace the BCM.
* Interior compartment lid release switch signal circuit terminal C
* Exterior compartment lid release switch signal circuit terminal B
4. Install a 3 A fused jumper wire between the signal circuit terminal listed below and ground. Verify the scan tool Trunk Release Switch parameter is Active.
* Interior compartment lid release switch signal circuit terminal C
* Exterior compartment lid release switch signal circuit terminal B
• If not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the BCM.
5. If all circuits test normal, test or replace the rear compartment lid release switch.
Rear Compartment Lid Latch Malfunction
1. Ignition OFF, disconnect the TRUNK relay.
2. Ignition ON, verify that a test lamp does not illuminate between the control circuit terminal 87 and ground.
• If the test lamp illuminates, test the control circuit for a short to voltage.
3. Verify that a test lamp illuminates between the B+ circuit terminal 85 and ground.
• If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit tests normal and the B+ circuit fuse is open, test the control circuit terminal 87 for a short to ground. If the circuit tests normal, test or replace the TRUNK relay.
4. Verify that a test lamp illuminates between the relay switch B+ circuit terminal 30 and ground.
• If the test lamp does not illuminate, test the B+ circuit for an open/high resistance.
5. Ignition OFF, disconnect the harness connector at the rear compartment lid latch.
6. Test for less than 5 ohm between the ground circuit terminal 3 and ground.
• If greater than the specified range, test the ground circuit for an open/high resistance.
7. Connect the harness connector at the rear compartment lid latch.
8. Ignition ON, connect a 10 A fused jumper wire between the B+ circuit terminal 30 and the control circuit terminal 87. Verify the rear compartment lid latch is activated.
• If the rear compartment lid latch does not activate, test the control circuit for an open/high resistance. If the circuit tests normal, test or replace the rear compartment lid latch.
9. Connect a test lamp between the B+ circuit terminal 85 and the control circuit terminal 86.
10. Command the Trunk Release ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.
• If the test lamp is always ON, test the control circuit for a short to ground. If the circuit tests normal, replace the BCM.
• If the test lamp is always OFF, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the BCM.
11. If all circuits test normal, test or replace the TRUNK relay.
Component Testing
Rear Compartment Lid Latch
1. Ignition OFF, disconnect the harness connector at the rear compartment lid latch.
2. Install a 10 A fused jumper wire between the control terminal 4 and 12 V. Install a jumper wire between the ground terminal 3 and ground. Verify the rear compartment lid latch activates.
• If the latch does not perform as specified, replace the rear compartment lid latch.
Rear Compartment Lid Release Switch
1. Ignition OFF, disconnect the harness connector at the appropriate rear compartment lid release switch.
2. Test for infinite resistance between the trunk release switch signal terminal and the ground terminal listed below with the switch in the open position.
* Interior compartment lid release switch signal terminal C and ground terminal A
* Exterior compartment lid release switch signal terminal B and ground terminal A
• If less than the specified value, replace the rear compartment lid release switch.
3. Test for less than 2 ohm of between the trunk release switch signal terminal and the ground terminal listed below with the switch in the closed position.
* Interior compartment lid release switch signal terminal C and ground terminal A
* Exterior compartment lid release switch signal terminal B and ground terminal A
• If greater than the specified range, replace the rear compartment lid release switch.
4. Test for infinite resistance between each terminal and the lid release switch housing/case.
• If less than the specified value, replace the rear compartment lid release switch.
Relay Test
1. Ignition OFF, disconnect the TRUNK relay.
2. Test for 65-90 ohm between terminals 85 and 86.
• If not the specified range, replace the relay.
3. Test for infinite resistance between the following terminals:
* 30 and 86
* 30 and 87
* 30 and 85
* 85 and 87
• If not the specified value, replace the relay.
4. Install a 10 A fused jumper wire between the relay terminal 85 and 12 V. Install a jumper wire between relay terminal 86 and ground. Test for less than 2 ohm between terminals 30 and 87.
• If greater than the specified range, replace the relay.
Repair Instructions
Perform the Diagnostic Repair Verification Verification Tests after completing the diagnostic procedure.
* Rear Compartment Lid Release Switch Replacement Rear Compartment Lid Release Switch Replacement
* Rear Compartment Lid Lock Cylinder Replacement Service and Repair
* Rear Compartment Lid Latch Replacement Service and Repair
* Relay Replacement (Attached to Wire Harness) Relay Replacement (Attached to Wire Harness)Relay Replacement (Within an Electrical Center) Relay Replacement (Within an Electrical Center)
* Control Module References Programming and Relearningfor BCM replacement, setup, and programming