Power Seat Inoperative
Power Seat Inoperative
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis Strategy Based Diagnosis for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions Diagnostic Procedure Instructionsprovides an overview of each diagnostic category.
Diagnostic Fault Information
Circuit/System Description
The power seat is controlled through the seat adjuster switch. Battery voltage is supplied at all times to the seat adjuster switch through the DRV SEAT 30 A fuse that is located in the rear fuse block. When the seat adjuster switches are in an inactive state, the switch contacts are closed to the switch ground circuit.
All seat motors are reversible. For example, when the seat horizontal forward switch is pressed to move the entire seat forward, battery voltage is applied through the switch contacts and the seat horizontal motor forward control circuit to the motor. The motor is grounded through the horizontal motor rearward switch contacts and the horizontal motor rearward control circuit to the motor. The motor runs in order to drive the entire seat forward until the switch is released. Moving the entire seat rearward works similarly to moving the entire seat forward, except that battery positive voltage and ground are applied on opposite circuits causing the motor to run in the opposite direction. All seat motors are powered this way.
Reference Information
Schematic Reference
Driver Seat Schematics [1][2]Electrical Diagrams
Connector End View Reference
Component Connector End Views Connector End Views By Name
Description and Operation
Power Seats System Description and Operation Description and Operation
Electrical Information Reference
* Circuit Testing Circuit Testing
* Connector Repairs Connector Repairs
* Testing for Intermittent Conditions and Poor Connections Testing for Intermittent Conditions and Poor Connections
* Wiring Repairs Wiring Repairs
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector at the seat adjuster switch.
2. Ignition OFF, test for less than 5.0 Ohms between the appropriate ground circuit terminals listed below and ground:
* 2-way power seat terminal A and terminal G
* 6-way power seat terminal B
• If greater than the specified range, test the ground circuit for an open/high resistance.
3. Ignition ON, verify that a test lamp illuminates between the appropriate B+ circuit terminal listed below and ground:
* 2-way power seat terminal F
* 6-way power seat Terminal D
• If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.
4. Ignition OFF, connect the harness connector at the seat adjuster switch and disconnect the harness connector at the appropriate seat motor.
5. Connect a test lamp between control circuit terminal A and control circuit terminal B.
6. Ignition ON, command the seat motor in both directions using the seat adjuster switch. The test lamp should turn ON when commanding the motor in both directions.
• If the test lamp remains OFF during either of the commands, test both control circuits for a short to ground or an open/high resistance. If the circuits test normal, test or replace the seat adjuster switch.
7. If all circuits tests normal, test or replace the seat motor.
Component Testing
Seat Adjuster Switch Test
1. Ignition OFF, disconnect the harness connector at the seat adjuster switch.
2. Test for infinite resistance between the B+ terminal and each control terminal with the switch in the open position.
• If not the specified value, replace the seat adjuster switch.
3. Test for less than 1 Ohms between the B+ terminal and each control terminal with the appropriate switch in the closed position.
• If greater than the specified range, replace the seat adjuster switch.
4. Test for less than 1 Ohms between the ground terminal and each control terminal with the switch in the open position.
• If greater than the specified range, replace the seat adjuster switch.
Seat Motors
1. Ignition OFF, disconnect the harness connector at the appropriate seat motor.
Note: When performing the following tests, make sure that the seat is not already in the position the test is attempting to produce.
2. Install a 30 A fused jumper wire between one motor control terminal and 12 V. Momentarily install a jumper wire between the other motor control terminal and ground. The seat motor should perform the appropriate UP/DOWN/FORWARD/REARWARD function.
• If the function does not perform as specified, replace the seat motor.
3. Reverse the jumper wires. The seat motor should perform operate in the opposite direction.
• If the function does not perform as specified, replace the seat motor.
Repair Instructions
Perform the Diagnostic Repair Verification Verification Tests after completing the diagnostic procedure.
* Driver or Passenger Seat Adjuster and Recliner Switch Replacement Driver or Passenger Seat Adjuster and Recliner Switch Replacement
* Front Seat Adjuster Motor Replacement Front Seat Adjuster Motor Replacement
* Seat Adjuster Motor Replacement - Horizontal Seat Adjuster Motor Replacement - Horizontal
* Seat Adjuster Motor Replacement - Vertical Seat Adjuster Motor Replacement - Vertical