Operation CHARM: Car repair manuals for everyone.

M/T - Installing Short Shift Kit

Boxster (986)
2/05

September 20, 2005

Short Shift Kit Installation Instructions

Note
This Technical information replaces Technical Information No. 3/03 dated October 24, 2003.

Vehicle Type:
Boxster (986)/Boxster S(986)

Model Year:
As of 1997 up to 2004

Restriction:
NOT for vehicles with Tiptronic transmission (I No. 249)

Note:
Shortening of shift travel will shorten the shift travel by up to 35%. This results in even more precise shift operations as well as an even sportier driving experience thanks to perfect shift control.

The setup for shortening the shift travel consists of a modified gearshift lever (precision milling part) and two new plastic bearings.





The Porsche logo can be seen on the gearshift lever when removed.

Part Number: 000.044.700.26 Shortening of shift travel





Parts List

Materials: 1X Polylub GYL 151 lubricant





Tools

Assembly:

1. Preparatory work

1.1 Remove right front seat --> POSES Workshop Manual Serv. No. 7201 "Removing front seat'.

1.2 Remove center console --> POSES, Workshop Manual, Serv. No. 6817 -"Removing center console".





1.3 Remove gearshift bracket.

1.3.1 Put gearshift lever in neutral.

1.3.2 Remove locking clips --> Figure 3 -A_ on support --> Figure 3 -B-.

1.3.3 Pull support --> Figure 3 -B- upwards out of the gearshift bracket.





Note
Do not loosen the locking sleeves --> Figure 4 -A- of the shift and selector cable.

1.3.4 Lever off shift cable --> Figure 4 -B- at the gearshift lever.

To do this, insert a large screwdriver through the side opening in the gearshift bracket and press end of shift cable down off the ball head.

1.3.5 Remove protective cap --> Figure 4 -C- and pull off selector cable --> Figure 4 -D-.





1.3.6 Unscrew nuts --> Figure 5 -A- and remove gearshift bracket.





2. Remove long gearshift lever (standard version).

DANGER
Risk of accidents (eye injuries) while removing the gearshift lever.

^ Wear protective goggles when knocking off the pins at the bushings (plastic).

2.1 Knock off pins --> Figure 6 -A- at the bushings (plastic) with a chisel.

2.2 Remove bushings from the gearshift bracket --> Figure 6 -Arrows-.

2.3 Guide gearshift lever --> Figure 6 -B- upwards out of the gearshift bracket.





3. Check whether a green clip --> Figure 7- Section- is installed on the base of the gearshift bracket.

3.1 If you see a green clip:

Press green clip downwards --> Figure 7 -Arrow A- and unclip it towards the front --> Figure 7- Arrow B- out of the gearshift bracket.

Background:

If the clip remains in the gearshift bracket, the shift cables will rub against the clip.

3.2 If there is no green clip:

Continue with the next step.

4. Install short gearshift lever.

4.1 Lightly lubricate pin and ball pin on the new gearshift lever using approx. 3 g of lubricant.





4.2 Guide gearshift lever into the gearshift bracket --> Figure 8- A-.

4.3 Position new bushing on gearshift bracket in such a way that the two pins stand vertically at the base of the bushing --> Figure 8 -D- and one groove in the bushing is aligned with the bar --> Figure 8 -A, Arrow- in the gearshift bracket.

4.4 Carefully press the bushing into the gearshift bracket using a vice --> Figure 8 -B- . When doing this, ensure that the gearshift lever pin is positioned in the bushing and the base of the bushing is flush with the --> Figure 8 -D- gearshift bracket.

4.5 Press the second bushing into the gearshift bracket in the same way --> Figure 8 -B-.

4.6 Check that the new gearshift lever moves smoothly in the bushing.

5. Concluding work:





5.1 Install gearshift bracket.

5.1.1 Insert the gearshift bracket and tighten nuts --> Figure 9 -A-.

Tightening torque: 10 Nm (7.5 ft-lb.)





5.1.2 Grease and attach selector cable --> Figure 10 -A-, than install protection cap --> 10 -B-.

5.1.3 Grease and fit shift cable --> Figure 10 -C-. To do this insert a large screwdriver through the side opening in the gearshift bracket and press end of shift cable onto the ball head.

5.1.4 Insert support --> Figure 10 -D- in gearshift bracket and secure with locking clips --> Figure 10 -E-.

5.2 Check shifting in all gears.

5.3 Install center console --> POSES, Workshop Manuel Serv. No. 6817 - "Installing center console".

5.4 Install right front seat --> POSES, Workshop Manuel, Serv. No. 7201 - "Installing front seat".

5.5 Test drive.





Working Time





References





Disclaimer