Lighting and Horns: Testing and Inspection

Electrics Maintenance: Checking the Function of the Vehicle's Lights
Turn on ignition, switch on all vehicle lights one after another and check that the individual lights are working.

Lights to be checked:
- Main headlights
- Fog lights
- Side direction indicator light
- Tail light
- Number plate light
- Additional brake light

Bulbs

Halogen headlights
- -1- Bulb for direction indicator light. PY 21 W, 12 V (yellow bulb).







- -2- Bulb for auxiliary high beam headlight. H7 (12 V, 55 W).
- -3- Bulb for high beam headlight. H7 (12 V, 55 W).
- -4- Bulb for parking light. H6 W (12 V, 6 W).
- -5- Bulb for dipped beam headlight. H7 (12 V, 55 W).

Xenon headlights
- -1- Bulb for direction indicator light. PY 21 W, 12 V (yellow bulb).







- -2- Bulb for auxiliary high beam headlight. H7 (12 V, 55 W).
- -3- Bulb for cornering light. H3 (12 V, 55 W).
- -4- Bulb for parking light. H6 W (12 V, 6 W).
- -5- Xenon gas discharge lamp for dipped beam and high beam. D1S (12 V, 35 W).

Tail light
- -A- Brake light. P 21 W.







- -B- Direction indicator light. P 21 W.
- -C- Reverse light. P 21 W.
- -D- Rear fog light and tail light. P 21/4 W.
- -E- Tail light. P 21/5 W.

Adjusting the Main Headlights
Flexible screwdriver 9703.
- The vehicle must be on a horizontal surface.
- Make the adjustment with the regulator switch set to 0 (headlight beam adjustment).
- Use flexible screwdriver 9703 with a hexagon bit to adjust the headlights.
- Make the adjustment with the vehicle ready for driving (fuel tank full, driver's seat occupied by a person or 75 kg, the tyre pressure must correspond to the stipulated values) using a headlight adjustment unit.

1. Press down the cover -1- in the engine compartment and remove it.







2. Turn on the ignition, turn on dipped beam and high beam headlights.
3. Check setting, adjust if necessary.

Adjusting:
- Set the headlight adjustment unit to 10 cm/10 m (1%).
- With this alignment, preference must be given to the central zone around the salient point of the light/dark limit.

NOTE:
- The distance between the headlights and the adjustment unit should be as small as possible.
- It should not exceed 30 cm, because if the distance is greater, it is no longer possible to define the formation of the light/dark limit in the adjustment unit clearly.







- The vertical/side adjustment of the dipped beam/high beam highlight is made first: adjustment -A- and -B-.

4. To do this, line up the light/dark borderline running upwards at an angle on the right-hand side with the dotted 15° line of the adjustment unit.







5. The dipped beam headlight is then adjusted horizontally: adjustment -A- and -B-.







- To do this, line up the left, horizontal section of the light/dark limit (when driving on the right) with the dotted horizontal line of the adjustment unit.







6. Check auxiliary high beam headlight and, if necessary, adjust the side setting using -A- and -B-.
7. In the case of Xenon headlights, the ignition must be switched off and on after the adjustment has been made with the lights switched on.
8. After this, the adjustment must be checked again.
9. Fit cap again.

Adjusting the main headlights, USA version

NOTE: A new adjustment may only be made in the case of accident repairs or replacement of the main headlights.

- Vertical and horizontal adjustment must be carried out with a headlight adjustment unit.

Checking Horn Function
Press horn actuation on steering wheel and check the function and sound of horn.