Suspension Alignment, Complete
Suspension alignment, completeThere are few differences between suspension alignment on the new 911 Turbo (996) and suspension alignment procedures on the 911 Carrera (996). This involves the vehicle height adjustment, the wheel-load difference from left to right, special tools and corrections to wheel alignment.
Modified quick-clamping holders are required for the 911 Turbo (996) (to fasten the measured-value pickups on the wheels). The quick-clamping holders present can be retrofitted by replacing the clamping units on the left and right. Supplier: Messrs. Beissbarth. These converted quick-clamping holders can also be used retroactively for the other Porsche models.
Note:
^ Observe the changed tightening torque when using the insert (tool -A-)!
Vehicle height/wheel load
Note:
^ There are few differences between suspension alignment on the new 911 Turbo and suspension alignment procedures on the 911 Carrera (996)!
^ As with the 911 Carrera (996) models, there is no adjustment facility for changing the vehicle height!
^ This applies to both the front and the rear axles!
^ Since the vehicle height cannot be adjusted, it is not possible to adjust (fine adjustment) the wheel-load difference between left and right at the rear and front axles!
The varying strength of pads between coil springs and spring seats on the right and left spring struts on the front and rear axles is not intended for changing the vehicle height but for compensating for differences in coil-spring load groups.
Because of the different equipment versions (additional equipment), a greater wheel-load difference between the left and right is permissible than previously was the case in Porsche suspension alignment for the 911 Carrera (996) (over 20 kg is possible). This is partly the result of heavier components compared with standard equipment and partly results from additional components that are asymmetrically arranged.
Wheel-alignment corrections
Rear axle
Warning:
Danger of injury and damage to property due to malfunctions in the PSM control range if the steering angle sensor is not calibrated or is calibrated incorrectly!
^ Calibrate steering angle sensor with wheels in straight-ahead position with the Porsche System Tester 2!
^ The steering angle sensor actual value must be checked after a suspension alignment which resulted in no changes being made to the wheel alignment values!
Note:
^ Similar to the 911 Carrera models (996), the kinematic toe-in is not adjustable!
^ Camber and toe can be adjusted via eccentrics!
Front axle
Warning:
Danger of injury and damage to property due to malfunctions in the PSM control range if the steering angle sensor is not calibrated or is calibrated incorrectly!
^ Calibrate steering angle sensor with wheels in straight-ahead position with the Porsche System Tester 2!
^ The steering angle sensor actual value must be checked after a suspension alignment which resulted in no changes being made to the wheel alignment values!
Note:
^ The caster is not adjustable!
^ After adjusting the toe, the lock nuts on the track rods must be tightened to the prescribed tightening torque of 50 Nm (37 ft. lbs.)!
^ The steering angle sensor must be calibrated if the previous wheel alignment values (on rear and/or front axle) were changed!
General procedure for suspension alignment
Note:
^ Carry out suspension alignment with an optical or electronic wheel alignment tester!
^ The measurement procedures should be taken from the operating instructions for the wheel alignment tester involved!
In order to exclude erroneous measurements, the following preconditions must be met before alignment and the following points should be given special attention:
^ Empty weight of vehicle in accordance with DIN 70020, i.e. car ready for the road, with full fuel tank, spare wheel (collapsible wheel) and tools.
^ Ball-joint and wheel-bearing play in order (wheel-bearing play cannot be adjusted).
^ Tyre pressure in accordance with regulations, fairly uniform tire tread.
^ Quick-clamping holder for the 911 Turbo with adapter (for the measured-value pickups) correctly secured to the wheels.
^ Receiving surfaces for the quick-clamping holder on the wheels and the adapter surfaces must be clean and flat. Always check the levelling surface on the wheels precisely in particular before fitting the quick-clamping holders.
^ Strictly comply with maintenance intervals for measuring equipment and measuring platform. If the levelling of the measuring platform or of the measuring area is done in-house, levelling equipment is required. A hose level is inadequate!
^ Skilled handling of measuring equipment and measuring platform.
^ Sliding plates with transverse motion (rotary motion) at the rear axle are advisable.
^ Observe the Technical Literature of PAG, the manufacturer of the measuring equipment and the manufacturer of the measuring platform.
^ Do not treat measured values as a whole, but very critically in regard to driving dynamics, high-speed strength of the tires, tire wear and cost/benefit effects (time required for correction of insubstantial deviations). The toe values are of decisive significance for driving dynamics and tire wear.
^ If the vehicle is measured front and rear, check and adjust the wheel alignment values at the rear axle first. Camber values at the front axle apply for the straight-ahead position of the wheels. Steering wheel and steering gear in center position when toe is being adjusted.
^ Before wheel alignment values are adjusted at front and rear axles, it is recommended that the vehicle height be checked at the DIN empty weight. Conclusions can then be drawn about wheel alignment values in the event of any suspension alignment that becomes necessary later.
Vehicle height (vehicle height check)
General
Note:
^ The vehicle height at front and rear axle is not adjustable!
Preliminary work
1. For the height check, place the vehicle on a level surface or on the measuring platform (ready to drive, with a full tank, spare wheel and tools).
2. Compress vehicle at front and rear by approximately 25 mm 2-3 times and allow it to spring back freely.
Front axle
Measure from road contact surface to the lower edge of the hexagon-head bolt of the tension-strut screw connection on the body!
Rear axle
Measure from wheel contact surface to the locating bore in the rear-axle side section (between toe and camber eccentrics)!
Wheel alignment
Warning:
Danger of injury and damage to property due to malfunctions in the PSM control range if the steering angle sensor is not calibrated or is calibrated incorrectly!
^ Calibrate steering angle sensor with wheels in straight-ahead position with the Porsche System Tester 2!
^ The steering angle sensor actual value must be checked after a suspension alignment which resulted in no changes being made to the wheel alignment values!
Note:
^ Only check or adjust wheel-alignment values when prescribed preconditions are met!
^ If the vehicle is measured front and rear, check and adjust the rear axle first!
^ After adjustment, tighten the appropriate screwed connections with the prescribed tightening torque!
^ The steering angle sensor must be calibrated if the previous wheel alignment values (on rear and/or front axle) were changed!
Rear axle
1. Prepare vehicle for checking and/or adjustment of wheel alignment values.
2. Place front wheels on rotary table and rear wheels on rotary/sliding plates.
3. Compress vehicle at front and rear by approximately 25 mm 2-3 times and allow it to spring back freely.
Adjusting camber
Warning:
Danger of injury and damage to property due to malfunctions in the PSM control range if the steering angle sensor is not calibrated or is calibrated incorrectly!
^ Calibrate steering angle sensor with wheels in straight-ahead position with the Porsche System Tester 2!
^ The steering angle sensor actual value must be checked after a suspension alignment which resulted in no changes being made to the wheel alignment values!
Note:
^ Use insert for torque wrench 9626 in combination with a torque wrench to loosen and tighten the lock nuts of the toe and camber eccentrics.
^ Prescribed tightening torque of the lock nut(s) = 100 Nm (74 ft. lbs.)! Adjusting value on the torque wrench (in contrast to earlier specifications) is also 100 Nm (74 ft. lbs.)!
- After loosening the lock nut, turn eccentric -B- appropriately.
Adjusting toe
Warning:
Danger of injury and damage to property due to malfunctions in the PSM control range if the steering angle sensor is not calibrated or is calibrated incorrectly!
^ Calibrate steering angle sensor with wheels in straight-ahead position with the Porsche System Tester 2!
^ The steering angle sensor actual value must be checked after a suspension alignment which resulted in no changes being made to the wheel alignment values!
Note:
^ Use insert for torque wrench 9626 in combination with a torque wrench to loosen and tighten the lock nuts of the toe and camber eccentrics.
^ Prescribed tightening torque of the lock nut(s) = 100 Nm (74 ft. lbs.)! Adjusting value on the torque wrench (in contrast to earlier specifications) is also 100 Nm (74 ft. lbs.)!
- After loosening the lock nut, turn eccentric -A- appropriately.
Front axle
Adjusting camber
Warning:
Danger of injury and damage to property due to malfunctions in the PSM control range if the steering angle sensor is not calibrated or is calibrated incorrectly!
^ Calibrate steering angle sensor with wheels in straight-ahead position with the Porsche System Tester 2!
^ The steering angle sensor actual value must be checked after a suspension alignment which resulted in no changes being made to the wheel alignment values!
The camber is adjusted by moving the spring strut transversely.
- For this purpose, loosen the -three outer fastening nuts- on the spring-strut mount and, to move the spring strut, remove the covering cap on the piston rod.
Adjusting caster
The caster is not adjustable.
Adjusting toe
Warning:
Danger of injury and damage to property due to malfunctions in the PSM control range if the steering angle sensor is not calibrated or is calibrated incorrectly!
^ Calibrate steering angle sensor with wheels in straight-ahead position with the Porsche System Tester 2!
^ The steering angle sensor actual value must be checked after a suspension alignment which resulted in no changes being made to the wheel alignment values!
Note:
^ The steering angle sensor must be calibrated if the previous wheel alignment values (on rear and/or front axle) were changed!
Preliminary work:
1. Check whether the steering wheel is displaced with respect to the steering gear.
2. To do this, center the steering gear as described below.
3. Turn wheels to the straight-ahead position.
4. Then readjust the front wheel alignment, if necessary, until pin No. -2- in driver No. -1- and the lug on the steering gear housing No. -4- line up.
No. -3- is the desired breaking point for pins in new steering gears. The (new) pin No. 2 is inserted into driver No. 1 and lies with its underside within the recess of lug No. 4. This locks the steering gear in the center position. After installation of a new steering gear, the lower part of the pin is sheared off (at the desired breaking point No. -3-) by turning the steering wheel. The upper part of the pin remains in the driver.
If necessary, reposition the steering wheel. When doing this, seek the best position.
Warning:
A triggering of the airbag (malfunction in the airbag system) caused by improper work on airbag components cannot be ruled out! In the case of such a malfunction, an unsuitable steering wheel holder could cause injury or damage!
^ Use only steering wheel holders which do not project into the area of the airbag unit!
^ Observe safety regulations when working with airbag vehicles!
5. Clamp steering wheel in center position with steering wheel holder.
Note:
^ Use only steering wheel holders which do not project into the area of the airbag unit!
6. If necessary, shorten the guide rod -A- at top -(arrow)-.
7. Then adjust toe at hexagon -2- of the track rod(s) after loosening the lock nut(s) -1-. The steering angle sensor must subsequently be calibrated by PSM!
Warning:
Danger of injury and damage to property due to malfunctions in the PSM control range if the steering angle sensor is not calibrated or is calibrated incorrectly!
^ Calibrate steering angle sensor with wheels in straight-ahead position with the Porsche System Tester 2!
^ The steering angle sensor actual value must be checked after a suspension alignment which resulted in no changes being made to the wheel alignment values!
Note:
^ In order to tighten the tie rod lock nut(s) to the prescribed tightening torque, use an insert for torque wrench 9625 in conjunction with a torque wrench!
^ The prescribed lock nut tightening torque of 50 Nm (37 ft. lbs.) corresponds to a setting on the torque wrench of approximately 35 Nm (26 ft. lbs.)!
Toe-difference angle
The toe-difference angle is not adjustable.