PCM 2.1(R) - Navigation Update
Tequipment31/07 ENU 9110 9
PCM2.1 - Navigation Update
Information
If the menu item is cancelled unintentionally, remove the navigation DVD and insert it again. The PCM2.1 automatically returns to the Update menu.
Vehicle Type: Cayenne/Cayenne S/Cayenne Turbo (1st & 2nd Generation)
Model Year: As of 2005 up to 2008
Filing: This bulletin replaces bulletin Group 9, # 31/07, dated November 30, 2007.
Information: New maps for navigation module
Restriction: Only for vehicles with PCM2.1
NOTE:
The navigation update kit 995.044.902.61, also called the Model Year (MY) 08 Navigation Update, contains the 3 disc shown above.
ATTENTION!
To ensure that the PCM2.1 integrated system and navigation software are updated correctly, the updates must only be performed by an authorized Porsche dealer.
Parts Information
Tools
Warning:
Malfunctions in the PCM2.1 system network due to open circuit when loading data.
-->Only run the engine if the exhaust extraction system is switched on.
Work Procedure
1. Preparatory work.
1.2 Connect battery charger. --> Workshop Manual "2X00IN01 Battery trickle charging"
1.2 Switch on ignition.
1.3 Switch on PCM2.1 by pressing the "on/Off" switch --> Figure 1 -A-.
1.4 Open the drawer for the telephone card --> Figure 1 -B-, remove the telephone card if there is one there and close the drawer again.
1.5 Press the eject button --> Figure 1 -C- and remove CD form the CD slot --> Figure 1 -D0-, id one was inserted.
2. Show current software version in PCM2.1 in the display.
2.1 press the "MAIN" and "TRIP" buttons --> Figure -E- and -F- simultaneously to go to the "SW versions" display.
2.2 Select "PCM" in the menu by turning the rotary knob --> Figure 1 -G- and press the knob to confirm your selection.
2.2.1 The relevant software version of the PCM2.1 will be displayed as shown above.
2.3 Select the steps above to be completed.
3. Update PCM2.1 to Model Level B software (software version 05024xxx) software.
3.1 Switch on ignition. If a battery charger is not connected, leave the engine running.
3.2 Insert the PCM2.1 Multimedia update CD 1 (part no. 000.043.205.47.002) into the CD slot of the PCM. The software update starts automatically.
3.3 The following message appears in the PCM2.1 display. "Updating software to Model Level B version" Press the rotary knob --> Figure 1 -G- to confirm the "YES" option.
3.4 The following message appears in the PCM2.1 display:
IMPORTANT:
After this update, a new navigation DVD will be required. Do you want to update? press the rotor knob to confirm the selection "YES" and to start the update.
Information
A software update updates the telephone control unit software as well as the PCM2.1 control module software. A bar showing the progress of the loading operation is displayed for each update step.
3.5 Depending on the vehicle equipment and the telephone, the information shown above will appear in the PCM2.1 display.
3.6 If the PCM2.1 does not switch on again automatically, switch on the PCM2.1 again by pressing the "ON/OFF" switch --> Figure 1 -A-.
3.7 Press the Eject button --> Figure 1 -C- and remove the update CD from the CD slot --> Figure 1 -D-.
4. Update the navigation system.
4.1 Remove the previously used navigation DVD from the navigation module under the passenger's seat.
4.2 Insert the PCM2.1 Multimedia Update CD Navigation (000.044.901.40) into the navigation module.
4.3 Switch off the PCM2.1 by pressing the ON/OFF button.
4.4 Switch off the ignition for approx. 2 minutes.
4.5 switch on ignition. If a battery charger is not connected, leave the engine running.
Information
If it does not start automatically, press "NAVI" button on the PCM2.1.
4.6 Switch on PCM2.1 and confirm the PCM2.1 display by pressing the right rotary knob.
4.7 The PCM2.1 screen displays the message shown above.
Information
The progress bar disappears once it reaches 10%. The display then remains at 0%.
4.8 The navigation update starts. After about 30 seconds, the PCM2.1 screen displays the message "Error starting navigation".
4.9 Remove the PCM2.1 Multimedia Update CD Navigation MY08 from the navigation module.
Information
After updating the PCM2.1 interated system to Model Level software, only the new navigation DVDs can be used.
4.10 Insert new navigation DVD (labeled 08.2007 or higher) into the navigation module. The following message appears in the PCM2.1 display" "Starting navigation system".
5. Concluding work
5.1 Insert the audio CD into the CD slot of the PCM2.1 if one was originally inserted.
502 Insert the telephone card into the drawer of the PCM2.1 if one was originally inserted.
5.3 Switch off the ignition.
5.4 Disconnect battery charger. --> Workshop Manual "2X00IN01 Battery trickle charging"
Working Time