Wheels/Tires - Approved Winter Wheels/Tires/Snow Chains
911 (997)23/08 ENU 4440
Approved Winter Tires, Wheels and Snow Chains
Vehicle Type:
911 Carrera 4 (997)/911 Carrera 45 (997)/911 Carrera 4 Cabriolet (997)/911 Carrera 4S Cabriolet (997)/911 Targa 4 (997)/911 Targa 45 (997)
Model Year:
As of 2009
Information:
Approved winter tire makes and types - June 2008.
WARNING
Driving with different tires (mixed tires)
- Uncontrollable vehicle handling
--> Only use tires of the same make and type, with the same speed index and the same specification code (N0, N1, N2,... ) on a vehicle.
Makes/Types:
Information:
N... = Specification code of the tire, e.g. "N0", "N1", "N2"... The complete "N..." code of the tires in question must be shown on the tire sidewall near the tire type designation.
Instructions for correct mounting of the tires are also given on the tire sidewall. If there are no mounting instructions on the tire sidewall, the tire must be mounted so that the DOT marking is visible from the outside.
Arrow with inscription "Rotation" = directional mounting
"Inside/Outside" inscription = mounting on specified side only.
Arrow with both inscriptions = directional on specified side only.
"Rotation" and "Inside/ Outside"
Information
If a tire is damaged and it is not possible to determine with absolute certainty that there is no ply damage - with all of its consequences - or if the tire was thermally and/or mechanically over loaded due to a loss of pressure or other prior damage, replace the tire in question for safety reasons.
Repairs to "V", "W", "Y" and "ZR" tires are not permissible, as well as the use of inner tubes in tubeless tires. Please inform your customers accordingly. It is advisable to mount winter tires at temperatures below 45 degrees F / 7 degrees C, because the driving characteristics of summer tires are reduced at low temperatures. Extremely low temperatures can cause permanent damage to summer tires.
WARNING
Incorrect tire pressure
- Uncontrollable vehicle handling
--> Adjust the tire pressure according to specifications. Never allow the pressure to fall below the minimum pressure.
--> Check age of tires. Replace tires that are more than 6 years old.
--> Perform visual inspections.
--> Use new rubber valves at every tire change.
--> Use only tires recommended by Porsche.
Tire Pressure:
Information:
The tire pressure applies only to the tire makes and types approved by Porsche, and is specified for cold tires (approx. 68 degrees F / 20 degrees C. The tire pressures must never be lower than the specified values.
Sizes:
WARNING
Wheel electronics units not detected, incorrectly secured or loose on vehicles without Tire Pressure Monitoring (TPM)
- Risk of damage to wheels and/or tires
- Uncontrollable vehicle handling
--> Do not mount wheels with wheel electronics units on vehicles without TPM.
Wheels:
Overview of Porsche wheels for winter tires
Identification on the inside/outside of the wheel disc:
Wheel size, rim offset (RO) in mm, Part No. and Porsche logo
Front: 8 J x 18 H2, RO 57
Part No. 997.362.137.01
Rear: 11 J x 18 H2, RO 51
Part No. 997.362.143.00
Front: 8 J x 19 H2, RO 57
Part No. 997.362.157.00
Rear: 11 J x 19 H2, RO 51
Part No. 997.362.163.01
Front: 8 J x 19 H2, RO 57
Part No. 997.362.156.03
Rear: 11 J x 19 H2, RO 51
Part No. 997.362.162.03
Front: 8 J x 19 H2, RO 57
Part No. 997.362.156.04
Rear: 11 J x 19 H2, RO 51
Part No. 997.362.162.06
Front: 8 J x 19 H2, RO 57
Part No. 997.362.156.02
Rear: 11 J x 19 H2, RO 51
Part No. 997.362.162.02
Information
Improper handling can damage the wheel surface.
Carry out tire removal and mounting using a bead holding-down device only.
Use a leather pad on the rim flange to support the valve insertion tool.
Only use the Porsche centering clamping set for balancing.
Do not use brushes to clean the wheels because brushes can cause deep scratches that cannot be removed by polishing.
Never use solvents or other chemical substances on tires.
Wheel Mounting:
Tightening torque 130 Nm (96 ftlb.)
WARNING
Incorrectly installed snow chains
- Uncontrollable vehicle handling
--> Do not exceed the maximum speed of Speed 50 km/h (30 mph).
--> Observe installation instructions from the chain manufacturer.
Snow Chains:
Information
Sufficient snow-chain clearance is only guaranteed by first removing any spacers that are installed.
Navigation Systems:
After a wheel or tire change, the full locating accuracy is attained only after a trip of approx. 30 miles (50 km), if possible on a highway and at a speed > 40 mph (60 km/h). Additionally, a high wheel slip factor (e.g, wheel spin on snow) can result in temporary incorrect positioning.
TPM Tire Pressure Monitoring System:
New wheels must be equipped with wheel transmitters for Tire Pressure Monitoring.
Check battery charge status of wheel transmitters before changing tires.
Switch off ignition when changing a wheel.
If the properties of the new tires do not correspond to the settings in the on-board computer, a message is displayed.
After changing a wheel, the tire settings in the on-board computer need to be updated (see operating instructions).
General:
Always use new valves when changing tires.
Always observe any possible instructions concerning the rolling direction and/or specifying which side the tires must be mounted on. Refer to notes (if applicable).
Coat the tire beads and humps with mounting lubricant before mounting the tire. This ensures that the tire beads will slide over the humps easily. In order to prevent the tire from turning on the wheel, avoid extreme driving maneuvers (acceleration and braking) during the first (100 to 200 miles) with new or recently mounted tires.
In order to optimize smoothness of rolling, it is appropriate - and necessary in individual cases - to mount the tire in a certain (favorable) position with respect to the wheel (matching).
Matching (uncontrolled and controlled) is explained below:
Uncontrolled matching:
Turning the tire on the wheel by 90 degrees or 120 degrees if necessary in order to achieve an acceptable value with regard to rolling smoothness (true running, imbalance and weight distribution of balance weights).
Controlled matching:
With a balancing machine with matching program. In most cases, this produces an even better result with regard to the rolling smoothness (true running, imbalance and weight distribution of the balance weights) than can be achieved with uncontrolled matching. Maximum permissible radial runout and lateral runout of the wheels < 0.7 mm. Maximum permissible radial runout and lateral runout of the wheels with tires < 1.25 mm. Values < 1.50 mm - ideally approx. 0.5 mm - are desirable.
The mounting pressure (seating pressure) of 58 psi / 4.0 bar overpressure must not be exceeded before both tire beads are evenly seated on the rim flange.
If new tires are to be mounted or the tires of one axle are to be replaced, tires of the same make, the same type and with the same specification code must always be used on each of the two axles. If tires are replaced on one axle only, the different tread depth from that on the other axle can cause a noticeable change in the familiar handling. This is especially the case if new tires are mounted on the rear axle. This effect decreases with increasing tire mileage.
When replacing a tire on an axle, make sure that the tread depth of the new tire does not differ from that of the other tire by more than 30 %.
If a tire is damaged and it cannot be determined with absolute certainty that there is no ply damage - with all of its consequences - or if the tire was thermally or mechanically overloaded due to a loss of pressure or other prior damage, we recommend replacement of the tire in question for safety reasons.
Repairs on "ZR" tires are not permissible, as is the use of inner tubes in tubeless tires. Tires age due to chemical and physical processes, which can impair their function. Tires that are stored unused for an extended period harden and become brittle faster than tires that are in continual use. Hairline aging cracks can occur on older tires. On tires in continual use, the kneading action activates the plasticizer in the rubber and there by prevents hardening and cracking.
Therefore, attention should be paid not only to the tread depth but also to the age of the tire. Tires should not be older than 6 years. The age of the tire can be determined via the DOT code on the sidewall, which indicates the production date of the tire: e.g. DOT 2201 = 22nd week of 2001.
Tires/complete wheels must be stored in a cool, dry and dark room with adequate ventilation. They must never come into contact with fuel, oil, grease or chemicals.
Complete wheels can be stacked for storage; it is advisable to increase the tire pressure by 0.4 bar. Optimum conditions for proper storage of the complete wheels are provided by the Original Porsche storage stand (trolley), Part Number 000 044 000 38.
If the tires are not mounted on wheels, it is best to store them in a vertical position. In this case the tires should be turned every two weeks in order to prevent excessive flattening. If the tires are stacked in horizontal position, they will become severely deformed and cannot be seated in the rim flange easily when they are fitted.
Disclaimer