405719 Removing and installing front wheel bearing

WM 405719 Removing and installing front wheel bearing

Tools









Technical values





Information

The wheel bearings adopt the function of the former ABS pulse rings. They are fitted with a so-called multipole seal. This is a seal with a magnetised layer, which generates the torque impulses for the ABS rpm sensors.

The multipole seal must not come into contact with highly magnetic parts.During installation, make sure that the magnetic side is facing the ABS sensor. Use test card 147-2 for this.





Wheel bearing





Preliminary work

- Remove front wheel bearing housing (wheel carrier). First, loosen the tension bolt on the wheel hub (lock nut on wheel hub/wheel bearing threaded joint).

Removing and installing front wheel bearing

Removing front wheel bearing

The following tools are required for removing the rear wheel bearing.





1. Take off brake cover plate on the wheel bearing housing.
2. Press out wheel hub.





Wheel bearing housing

Press the wheel hub out using a press-out mandrel P 297a. Separating device (dia. = 12 - 115 mm) Nr.111 and a suitable support must be used for countering.
3. Remove cover for wheel bearing on the wheel bearing housing.
4. Heat wheel bearing housing to approx. 100 °C (max. 120 °C).

CAUTION

Hot components

- Risk of burns

-> Let hot components cool down.
-> Wear personal protective gear.

CAUTION

Hot components

- Risk of burns

-> Let hot components cool down.
-> Wear personal protective gear.

5.
Press out wheel bearing using a tubular piece VW 415 A.





Pressing out wheel bearing

6. Press out wheel bearing inner race.

Information

To press out the inner bearing race of the old wheel bearing, pull the inner bearing race several millimetres off the wheel hub using a two-claw puller so that the separator can be put into place. To do this, use a two-claw puller together with a pressure piece VW 433, for example.





Pressing out bearing race

Pull inner bearing race several millimetres off the wheel hub using a two-claw puller.
Press out inner bearing ring using a press-out mandrel P 297a together with the separating device (dia. = 12 - 115 mm) Nr.111.

Installing front wheel bearing

Before installation, clean the bore in the wheel bearing housing and remove edges with a polishing cloth.

The following tools are required for installing the rear wheel bearing.





1. Press in wheel bearing.

Information

The wheel bearings adopt the function of the former ABS pulse rings. They are fitted with a so-called multipole seal. This is a seal with a magnetised layer, which generates the torque impulses for the ABS rpm sensors.

The multipole seal must not come into contact with highly magnetic parts.During installation, make sure that the magnetic side is facing the ABS sensor. Use test card 147-2 for this.

Preparatory condition:=> Temperature: 100°C
1.1. Heat up wheel bearing housing before pressing in the wheel bearing.





Pressing in wheel bearing

CAUTION

Hot components

- Risk of burns

-> Let hot components cool down.
-> Wear personal protective gear.

CAUTION

Hot components

- Risk of burns

-> Let hot components cool down.
-> Wear personal protective gear.

1.2. Insert wheel bearing at the correct position, then press again on the wheel bearing housing with only slight force using a suitable pressure piece (9247/4), see pressure piece (4 x) 9247 and tubular piece VW 415 A.
2. Fit cover for wheel bearing on the wheel bearing housing.=> Tightening torque: 37 Nm (27 ftlb.).
3. Press in wheel hub.





Pressing in wheel hub

Position wheel bearing housing on wheel hub and press on wheel bearing inner race using a tubular piece VW 415 A.
4. Fit brake cover plate on wheel carrier.
Screw in and tighten screws on brake cover plate.
=> Tightening torque: 10 Nm (7.5 ftlb.)

Subsequent work

1. Install wheel bearing housing.
1.1. Tighten tension bolt on the wheel hub (wheel hub/wheel bearing threaded joint). Use a new lock nut (M22 x 1.5). Tightening torque: 460 Nm (340 ftlb.).