PCM3.0(R) - Bluetooth(R) Hands-Free Interface

PCM3.0 - Bluetooth Hands-free Interface (l-no. 619)

Concerns:
Retrofitting

Model Year:
As of 2009

Restriction:
Only for vehicles with PCM3.0 (l-no. 665) or navigation system (l-no. 672). Not in conjunction with telephone module (l-no. 666).

NOTE:
The mobile phone preparation is available without a console for connecting mobile phones that support the hands-free profile (HFP) via Bluetooth(R). When connected over HFP, PCM3.0 serves only as a hands-free facility. The mobile phone can remain packed. The telephone numbers from the SIM card must be copied over manually, unlike with the telephone module. Only the basic functions of the mobile phone can be used using PCM3.0 (see PCM3.0 operating instructions). With this option, GSM is connected via the mobile phone antenna.

If a mobile phone is installed and activated even though the telephone module is installed, the telephone module is not required. Both systems cannot be used at the same time.

After ordering, i.e. entering the part number and Vehicle Identification Number (VIN) in POLARIS Lock/Key parts order screen, the enabling code should be displayed within one day once the VIN is entered in the Vehicle code information column in the PIWIS information system.

Parts Info:
997.044.902.33-> Mobile phone preparation, set

Parts List:





Materials:
--- -- Wrapping tape (commercially available)

Tools:
3IWIS Tester 9718
Press-out tool set Nr. 155 Pos. 1

System Diagram:

INFORMATION For a better understanding of the system layout, see system diagram , Figure 3.





Work Procedure:

INFORMATION If a wire harness for microphones does not need to be installed (for details of options, see Step 2.1 Overview of installing microphone wire harness), only Steps 1.1 and 4.4 have to be completed -Enable mobile phone preparation.

1. Preparatory work.
1.1 Connect battery charger. --> Workshop Manual '2X00IN03 Battery trickle charging'
1.2 Remove PCM3.0. --> Workshop Manual '911019 Removing and installing PCM 3.0 display and operator control unit'
1.3 Remove trim panel under dashboard. --> Workshop Manual 701919 Removing and installing trim panel under dashboard'-Checking

2. Install microphone wire harness.

INFORMATION The table shows whether a microphone wire harness needs to be retrofitted.

2.1 Overview of installing microphone wire harness:

Vehicle equipment Microphone wire harness Installation
BOSE sound package (l-no. 680) Yes
ASK sound package (l-no. 490) Yes
Telephone module (l-no. 666) No
Telephone module (l-no. 666)
in conjunction with l-nos. 490, 680. No
Voice control system (l-no. 671) No
Voice control system (l-no. 671)
in conjunction with l-nos. 490, 666, 680. No

2.2 Prepare wire harness for microphone.







2.2.1 Open lock on white connector housings Figure 4 -1-.

INFORMATION Ensure socket contact is seated securely.

2.2.2 Insert socket contact of line BU 0.35sq. into chamber 1 of the white connector housing.
Insert socket contact of line YE 0.35sq. into chamber 2 of the white connector housing.

2.2.3 Close lock on white connector housing.







2.2.4 Lift up locking mechanism --> Figure 5 -arrow A- on wire harness for microphones and pull the plug socket --> Figure 5 -1- out of the plug carrier --> Figure 5 -arrow B-.





2.3 Open wiring duct --> Figure 6 -1-.





2.4 Route wire harness for microphones --> Figure 7-1- and secure with a tie-wrap or wrapping tape.
Steering column --> Figure 7-2-> into wiring duct-> Figure 7-3- > main wire harness --> Figure 7-4- > PCM installation slot

2.5 Close wiring duct.

INFORMATION Socket contacts also need to be changed, depending on the vehicle equipment.

2.6 Only for vehicles with BOSE sound system (l-no. 680) or ASK sound package (l-no. 490) or TV tuner (l-no. 676): Change socket contacts.
2.6.1 Overview of socket contacts to be changed.








2.6.2 Press locking mechanism down --> Figure 8 -arrow A- and pull standard connector module C (coding: blue) --> Figure 8 -1- out of the PCM central connector --> Figure 8 -2- (--> Figure 8 -arrow B-).





2.6.3 Lift up locking mechanisms =>Figure 9 -arrow A- and pull the plug socket --> Figure 9 -1- out of the plug carrier --> Figure 9 -arrow B-.

INFORMATION Ensure socket contact is seated securely.





2.6.4 Press socket contact of WH/RD line (chamber C4), for example, out of the standard connector housing --> Figure 10 -1- using a press-out tool and insert it into the connector housing (retrofit kit) --> Figure 10 -2-.





2.7 Insert plug socket --> Figure 11 -1- into plug carrier =>Figure 11 -2-.





2.8 Insert connector module C (coding: blue) --> Figure 12 -arrow- from the microphone wire harness into the PCM central connector.
2.9 Only for vehicles with BOSE sound package (l-no. 680):





2.9.1 Open lock on microphone connector housing --> Figure 13 -1-.
2.9.2 Press socket contacts out of the connector housing using press-out tool 88089.

INFORMATION Ensure socket contact is seated securely.





2.9.3 Insert socket contact of line RD 0.5sq. into chamber 3 of the white connector housing --> Figure 14
Insert socket contact of line RD/BN; 0.5sq. into chamber 4 of the white connector housing.
2.9.4 Close lock on white connector housing.

3 Install microphones.

INFORMATION Either two microphones or no microphones must be retrofitted, depending on the vehicle equipment.

3.1 Overview of microphone fixtures

Vehicle equipment Microphone installation
BOSE sound package (l-no. 680) Yes
ASK sound package (l-no. 490) Yes
Telephone module (l-no. 666) No
Telephone module (l-no. 666)
in conjunction with l-nos. 490, 680. No
Voice control system (l-no. 671) No
Voice control system (l-no. 671)
in conjunction with l-nos. 490, 666, 680. No

3.2 Install microphone.





3.2.1 Unclip the standard microphone (e.g. BOSE sound system, coding: black) --> Figure 15-1- from the trim panel.





3.2.2 Clip sound microphone/hands-free microphone (coding: white) --> Figure 16 -2- and hands-free microphone (coding: light blue) --> Figure 16-1- into the trim panel.

4 Concluding work





4.1 Fit new tie-wraps ->Figure 17-1-o on trim panel under the dashboard.
4.2 Install trim panel under dashboard (driver's side). --> Workshop Manual 701919 Removing and installing trim panel under dashboard'
4.3 Install PCM3.0. --> Workshop Manual '911019 Removing and installing PCM 3.0 display and operator control unit'

NOTICE
Voltage drop
- Risk of irreparable damage to control unit
- Risk of damage to control unit
- Fault entries in the control unit
- Coding in the control unit is aborted
- Malfunctions in control unit, even during programming

- Switch off the ignition and remove the ignition key before disconnecting the control unit.
- Ensure that the power supply is not interrupted during programming.
- Connect a battery charger with a current rating of at least Nominal value 40 A to the vehicle battery.

INFORMATION
- The PIWIS Tester 9718 instructions take precedence and in the event of a discrepancy these are the instructions that must be followed. Deviations may occur with later software versions.
- The procedure described here has been structured in general terms; different text or additions may appear in the PIWIS Tester 9718.

4.4 Enable mobile phone preparation.
4.4.1 PIWIS Tester 9718 must be connected and ignition switched on.
4.4.2 Select vehicle type and run control unit search.
4.4.3 Select PCM3 control unit.
4.4.4 Select PCM3 in the PCM3 function selection menu. Press F12 to continue.
4.4.5 Select Coding in the PCM3 function selection menu. Press F12 to continue.
4.4.6 Select Enabling code in the PCM3/Coding menu. Press F12 to continue.

INFORMATION The PIWIS Tester 9718 displays the message not installed/not enabled/not operational.

4.4.7 Select Enabling code for Bluetooth mobile phone preparation in thePCM3.0/Enabling code menu. Press F12 to continue.
4.4.8 Enter the enabling code and press F8 to start coding. PIWIS Tester 9718 then displays the message installed/enabled/functional.
4.4.9 Press F11 to return to the main menu. The system is initialized.
4.4.10 Once coding is complete, read out the fault memories of all systems, correct any existing faults and erase the fault memories.
4.4.11 Switch off ignition and disconnect PIWIS Tester 9718.
4.4.12 Disconnect the battery charger. --> Workshop Manual '2X00IN03 Battery trickle charging'





Working Time:





Disclaimer