741319 Removing and installing cover for front seat (folding sports bucket seat)
WM 741319 Removing and installing cover for front seat (folding sports bucket seat)
Tools
Technical values
Tools and materials
Scudding knife P 9747
Knurling tool P 9747/1
Bone burnisher P 9747/2
Hot-air gun v.a.g 1416
Preliminary work
1. Remove sports bucket seat. -> 720119 Removing and installing folding sports bucket seat - section on "Removing" 720119 Removing and installing folding sports bucket seat
2. Fit sports bucket seat on assembly fixture. -> 7201IN Mounting front seat on assembly fixture 7201IN Mounting front seat on assembly fixture
Information
Only for cover for side of seat.
3. Remove bottom belt strap guide at the left and right. -> 692619 Removing and installing belt strap guide (folding sports bucket seat) - section on "Removing" 692619 Removing and installing belt strap guide (folding sports bucket seat)
Removing cover for front seat
Removing seat cushion (front part)
Installation position of seat cover (folding sports bucket seat)
1. Pull seat cushion -1- off the Velcro fasteners -2- on the seat shell -3- ( -arrow- ).
Removing seat cushion (front part)
Removing seat cushion (rear part)
Installation position of seat cover (folding sports bucket seat)
1. Pull seat cushion -1- off the Velcro fasteners -2- on the seat shell -3- ( -arrow- ).
Removing seat cushion (rear part)
Removing cover for side of seat
Installation position of seat cover (folding sports bucket seat)
CAUTION
Risk of damage to seat shell from fastening clamps.
- Risk of surface damage (scratches).
-> Mask the seat shell with adhesive tape.
-> Remove fastening clamps from the cover (joint).
1. Mask the seat shell -1- in the marked area with adhesive tape -2- (2-3 layers).
Masking seat shell
2. Carefully pull cover -1- off the Velcro fastener -2- close to the belt strap guide -arrows A-.
Removing inner cover
3. Pull off cover -1- at the Velcro fasteners -3- ( -arrows B- ).
4. Fold cover -1- outwards -arrows-.
Folding cover over
5. Pull cover off the seat shell.
Removing cover
5.1. Carefully pull cover -1- out of the seat shell -2- starting at the back -arrows A-.
If the fastening clamps -3- are also pulled off, remove them from the cover immediately -arrow B-.
5.2. Press the removed fastening clamps -3- into the seat shell.
5.3. Disengage cover -1- at the fastening clamps -4- at the front -arrow C-.
Installing cover for front seat
Installing cover for side of seat
1. Check fastening clamps -1- and replace them if necessary.
Checking clamps
2. Check fastening clamp -2- and replace if necessary.
3. Secure cover.
Securing cover
3.1. Fit and straighten cover -1- ( -arrows A- ).
3.2. Press cover into the seat shell -2- at the sides -arrow B-.
3.3. Press cover into the fastening clamp -3- at the front -arrow C-.
4. Fold cover -1- inwards -arrows-.
Securing cover
Information
Make sure the Velcro fasteners join cleanly.
5. Press Velcro fasteners -3- onto the seat shell -2- ( -arrows A- ).
Pressing on Velcro fasteners
6. Straighten cover -1- close to the belt strap guide and press it onto the Velcro fastener -2- ( -arrows B- ).
7. Press joint on cover -1- into the seat shell -2- at the sides using a plastic wedge and secure by tapping gently (with a plastic hammer).
Securing cover
8. Remove adhesive tape -2- from the seat shell -1-.
Removing adhesive tape
Installing seat cushion (rear part)
1. Position seat cushion -1- on the seat shell -3- ( -arrow- ) and straighten it. Press on Velcro fasteners -2-.
Installing seat cushion (rear part)
Installing seat cushion (front part)
1. Position seat cushion -1- on the seat shell -3- ( -arrow- ) and straighten it. Press on Velcro fasteners -2-.
Installing seat cushion (front part)
Subsequent work
Removing creases in seat cover (leather)
CAUTION
Risk of damage to cover if excessive heat is applied.
- Creases in cover
-> If creases have formed, only short partial warming with the hot-air gun is permissible.
-> The hot-air temperature must always be => Temperature: 50°C.
1. If creases have formed, partially heat the affected areas of the cover with the hot-air gun and smooth out the cover using the special tool.
Scudding knife P 9747
Knurling tool P 9747/1
Bone burnisher P 9747/2
Hot-air gun v.a.g 1416
Subsequent work
Information
Only for cover for side of seat.
1. Install bottom belt strap guide at the left and right. -> 692619 Removing and installing belt strap guide (folding sports bucket seat) - section on "Installing" 692619 Removing and installing belt strap guide (folding sports bucket seat)
2. Remove sports bucket seat from the assembly fixture and install it. -> 720119 Removing and installing folding sports bucket seat - section on "Installing" 720119 Removing and installing folding sports bucket seat