973219 Removing and installing wire harness for door
WM 973219 Removing and installing wire harness for door
Information
Component information - front door
Installation position of wire harness for front door
Component information - rear door
Installation position of wire harness for rear door
Preliminary work
Preliminary work for front door panel
1. Remove front door panel. -> 705919 Removing and installing front door panel - section on "Removing" 705919 Removing and installing front door panel
Preliminary work for rear door panel
1. Remove rear door panel. -> 707319 Removing and installing rear door panel - section on "Removing" 707319 Removing and installing rear door panel
Preliminary work for front door sub-frame
1. Remove front door sub-frame. -> 573019 Removing and installing front door sub-frame - section on "Removing" 573019 Removing and Installing Front Door Sub-Frame
Preliminary work for rear door sub-frame
1. Remove rear door sub-frame. -> 583019 Removing and installing rear door sub-frame - section on "Removing" 583019 Removing and Installing Rear Door Sub-frame
Removing wire harness for door
Removing wire harness for door in front door panel
Information
The number of plug connections can vary, depending on equipment.
1. Carefully detach insulating mat at the bonding points and remove it.
Detaching insulating mat
2. Disconnect electric plug connections.
2.1. Pull off electric plug connection for alarm system LED -1-.
Pulling off connector on alarm system LED
2.2. Release light for door opener -A- and pull it off -B-.
Pulling off light for door opener
2.3. Release electric plug connection for mid-range loudspeaker -a- and pull it off -B-.
Pulling off connector on mid-range loudspeaker
2.4. Release electric plug connection for power windows switch -a- and pull it off -B-.
Pulling off connector on power windows
2.5. Release light for storage box -A- and pull it off -B-.
Pulling off light for storage box
3. Unclip fixing clips for wire harness.
Unclipping fixing clips
Removing wire harness for door in rear door panel
Information
The number of plug connections can vary, depending on equipment.
1. Carefully detach insulating mat at the bonding points and remove it.
Detaching insulating mat
2. Disconnect electric plug connections.
2.1. Release light for door opener -A- and pull it off -B-.
Pulling off light for door opener
2.2. Pull off light for ashtray -1-.
Pulling off connector on ashtray
2.3. Pull off electric plug connection for power windows switch.
Pulling off connector on power windows
2.4. Pull off electric plug connection for door warning light.
Pulling off connector for door warning light
3. Unclip fixing clips for wire harness.
Unclipping fixing clips
Removing wire harness for door in front door sub-frame
Information
The number of plug connections can vary, depending on equipment.
1. Disconnect electric plug connections.
1.1. Release electric plug connection at the bracket -1- ( -A- ) and pull it off -B-.
Disconnecting connector on door control unit
1.2. Release electric plug connections -2- , -3- for door wire harness at the door control unit -a- and pull them off -C- , -D-.
1.3. Release electric plug connection for power windows motor -a- and pull it off -B-.
Pulling off connector on power windows motor
1.4. Release electric plug connection for pressure sensor -a- and pull it off -B-.
Pulling off connector on pressure sensor
1.5. Release electric plug connection for woofer -a- and pull it off -B-.
Pulling off connector on woofer
2. Unclip fixing clips for wire harness at the inside.
Removing inner fixing clips
3. Unclip fixing clip at the outside -A-.
Removing outer fixing clip
4. Press rubber sleeves out of the opening in the door sub-frame -B-.
5. Guide wire harness out of the door sub-frame.
Removing wire harness for door in rear door sub-frame
Information
The number of plug connections can vary, depending on equipment.
1. Disconnect electric plug connections.
1.1. Release electric plug connection for door wire harness at the door control unit -a- and pull it off -B-.
Disconnecting electric plug connection
1.2. Release electric plug connection -4- for door wire harness at the door control unit -a- and pull it off -B-.
Disconnecting plug connection
1.3. Release electric plug connection for power windows motor -a- and pull it off -B-.
Pulling off connector on power windows motor
1.4. Release electric plug connection for woofer -a- and pull it off -B-.
Pulling off connector on woofer
2. Unclip fixing clips for wire harness at the inside.
Removing inner fixing clips
3. Press rubber sleeves out of the opening in the door sub-frame.
Removing rubber sleeves
4. Guide wire harness out of the door sub-frame.
Installing wire harness for door
Installing wire harness for door in front door sub-frame
Information
The number of plug connections can vary, depending on equipment.
1. Guide wire harness into the door sub-frame.
2. Clip in fixing clip for wire harness for door sub-frame at the outside.
Securing wire harness to the outside
3. Press rubber sleeves into the opening in the door sub-frame. Check that they are seated securely.
4. Clip in fixing clips for wire harness for door sub-frame at the inside.
Securing wire harness at the inside
5. Plug in electric plug connections.
5.1. Plug in electric plug connection for pressure sensor until it engages securely.
Plugging in connector on pressure sensor
5.2. Plug in electric plug connection for power windows motor until it engages securely.
Plugging in connector for power windows motor
5.3. Plug in electric plug connection for woofer until it engages securely.
Plugging in connector for woofer
6. Plug in electric plug connections on the door control unit.
Plugging in connector on door control unit
6.1. Clip electric plug connection into the bracket -A-.
6.2. Plug in electric plug connection on the door control unit -B- and -C- until it engages securely.
6.3. Plug in and lock electric plug connection on the door control unit -D-.
Installing wire harness for door in rear door sub-frame
Information
The number of plug connections can vary, depending on equipment.
1. Guide wire harness into the door sub-frame.
2. Clip in wire harness at the door sub-frame.
Clipping in wire harness
3. Press rubber sleeves into the opening in the door sub-frame. Check that they are seated securely.
Securing rubber sleeves
4. Plug in electric plug connections.
4.1. Plug in electric plug connection for woofer until it engages securely.
Plugging in connector for woofer
4.2. Plug in electric plug connection for power windows motor until it engages securely.
Plugging in connector on power windows motor
5. Plug in electric plug connections on the door control unit.
Plugging in connectors on door control unit
5.1. Clip electric plug connection into the bracket -A-.
5.2. Plug in electric plug connection on the door control unit -B- and -C- until it engages securely.
5.3. Plug in and lock electric plug connection on the door control unit -D-.
Installing wire harness for door in front door panel
Information
The number of plug connections can vary, depending on equipment.
1. Secure fixing clips.
Securing fixing clips
2. Plug in electric plug connections.
2.1. Plug in light for storage box until it engages securely.
Plugging in light for storage box
2.2. Plug in electric plug connection for power windows switch until it engages securely.
Plugging in connector on power windows switch
2.3. Plug in electric plug connection for mid-range loudspeaker until it engages securely.
Plugging in connector on mid-range loudspeaker
2.4. Plug in light for door opener until it engages securely.
Plugging in light for door opener
2.5. Plug in plug connection for alarm system LED -1-.
Plugging in connector on alarm system LED
3. Fit insulating mat and affix it securely to the bonding points with hot-melt adhesive.
Installing wire harness for door in rear door panel
Information
The number of plug connections can vary, depending on equipment.
1. Secure fixing clips.
Securing fixing clips
2. Plug in electric plug connections.
2.1. Plug in electric plug connection for door warning light until it engages securely.
Plug in connector on door warning light
2.2. Plug in electric plug connection for power windows switch. Check that it is seated securely.
Plugging in connector on power windows switch
2.3. Plug in light for ashtray -1- until it engages securely.
Plugging in light for ashtray
2.4. Plug in light for door opener until it engages securely.
Plugging in light for door opener
3. Fit insulating mat and affix it securely to the bonding points with hot-melt adhesive.
Subsequent work
Subsequent work for front door sub-frame
1. Install front door sub-frame. -> 573019 Removing and installing front door sub-frame - section on "Installing" 573019 Removing and Installing Front Door Sub-Frame
Subsequent work for rear door sub-frame
1. Install rear door sub-frame. -> 583019 Removing and installing rear door sub-frame - section on "Installing" 583019 Removing and Installing Rear Door Sub-frame
Subsequent work for front door panel
1. Install front door panel. -> 705919 Removing and installing front door panel - section on "Installing" 705919 Removing and installing front door panel
Subsequent work for rear door panel
1. Install rear door panel. -> 707319 Removing and installing rear door panel - section on "Installing" 707319 Removing and installing rear door panel