Tire Monitor System - Spare Parts Requirements

Service

4

25/10 ENU 4434

Jun 11, 2010

The present document was valid at the time of print. A later version may be available online

Spare Parts Requirements for Tire Pressure Monitoring Control Unit (25110)

Model year:

2010

Information

This Technical Information replaces the TI dated May 3, 2010. Changes/additions compared to the previous Technical Information:

--> Working time values 30 and 150 TU added under "Working Time".

Vehicle Type:

Panamera S/Panamera Turbo

Concerns:

Water leakage in tail light/rear side panel area at the right.

Information:

Spare parts requirements for control units...

- Tire Pressure Monitoring system (referred to below as "TPM"),

and/or

- Reversing camera.





It is possible that the body of some vehicles was not sealed sufficiently in the tail light area (rear side panel at the right and/or left) at the beginning of series production.

As a result, water can get into the vehicle through a small gap (-inset/arrow-).
(Figure shows right side of the vehicle).

The TPM and reversing camera control units are located inside the vehicle in the rear side panel area at the right.

Action Required:
If spare parts are required or if the TPM and/or reversing camera control units need to be replaced, perform a visual inspection to see if there is any moisture in the side panel area at the right and/or close to the control units.

If there is: see --> "Procedure" section --> starting at Step --> 1

If not: see --> "Procedure" section --> only Step --> 1 (Replace control unit(s)).

Parts Info:

000.043.204.38 --> Sealing material

Tools/Materials:

Clean cloth
Sealing material
Shop light, if necessary
Degreasing cleaning agent (e.g. isopropanol)

Work Procedure:

1 Replace control unit(s), see --> 443455 Replacing TPM control unit and/or --> 917355 Replacing control unit for reversing camera.

Is there moisture in the side panel area at the right or close to the control units?

If there is: --> 2
If not: End of action required.

2 Absorb any moisture in the area with a dry cloth.

3 Remove rear right tail light, see 943119 Removing and installing tall light.

4 Clean the gap area on the body (--> Figure 1) using a cloth and degreasing cleaning agent (e.g. isopropanol).

4.1 Seal the gap using sealing material (000.043.204.38).

5 Install tail light, see 943119 Removing and installing tall light.

6 Remove rear left tail light and check to see if there is a gap on the body (same as right side, Figure 1). If there is: Proceed as described under 7

If not: Install tail light, see 943119 Removing and installing tall light. End of remedial action.

7 Work on the left side of the vehicle.

7.1 Remove side trim panel at the left, see 700319 Removing and installing side trim panel for rear luggage compartment.

7.2 Absorb any moisture in the area with a dry cloth.

7.3 Install side trim panel, see 700319 Removing and installing side trim panel for rear luggage compartment.

7.4 Clean the gap area on the body (--> Figure 1) using a cloth and degreasing cleaning agent.

7.4.1 Seal the gap using sealing material (000.043.204.38).

7.5 Install tail light, see 943119 Removing and installing tail light End of remedial action.





Working Time:

44344941: Reworking TPM and/or reversing camera control unit; Labor time 30 ZE

References 1:

--> 443455 Replacing TPM control unit

--> 917355 Replacing control unit for reversing camera

--> 700319 Removing and installing side trim panel for rear luggage compartment

--> 943119 Removing and installing tall light

References 2:

--> 917300 Spare parts requirements for control unit for reversing camera (25/10)

--> 970120, 970121, 970420, 970421, 970430, 970431

Model year 2010
C02, C36