610919 Removing and installing hood inner lining
WM 610919 Removing and installing hood inner lining
Preliminary work
1. Move hood to service position. -> 6101IN IN -Hood service position
2. Remove hood lock. -> 611919 Removing and installing hood lock - section on "Removing" Service and Repair
Removing hood inner lining
Removing front hood inner lining
Installation position of hood inner lining
1. Unscrew fastening screws at the left and right -arrow-.
Unscrewing fastening screws
2. Pull off sewn-on clamping rail at the front of the roof frame (1) at the left and right -arrows-.
Pulling off front clamping rail
3. Pull off sewn-on clamping rail at the back of the roof frame (1) at the left and right -arrows-.
Pulling off rear clamping rail
4. Remove expanding clip -1- from the covering strip -2- and roof frame (1) at the rear -arrow-.
Loosening hood inner-lining joint on roof frame
5. Open the Velcro fastener -1- at the left and right between the hood inner lining at the side -2- and the corner bow -3- ( -arrow- ).
Loosening Velcro fastener
6. Open the Velcro fastener on the headliner at the left and right on the corner bow -arrow-.
Opening Velcro fastener
7. Unscrew fastening screw -4- at the left and right from the bracing straps -1 to 3- ( -arrows- ).
The wire harness for the hood -5- is also secured on the left side.
Removing bracing straps
8. Unscrew fastening screws -1- at the left and right from the hood inner-lining joint -2- ( -arrow- ).
Removing hood inner-lining joint
9. Disconnect the hood inner lining at the front -1- by opening the zip -2- in -direction of arrow- and detach it from the hood covering -3-.
Release the zip using a paper clip -4-.
Opening zip
10. Unscrew fastening screw -1- at the left and right from the bracing strap -2- and from the hood inner lining at the rear -3- ( -arrow- ).
Loosening bracing strap
11. Use a plastic spatula to press the joint strip -1- on the hood inner lining out of the rear groove on the corner bow -arrows A-.
Removing corner bow joint
12. Slide the hood inner-lining joint -2- out of the front groove on the main folding top bow in -direction of arrow B-.
Removing hood inner lining at rear
1. Detach the hood inner lining at the rear -3- by opening the zip -2- on the hood covering -1- in -direction of arrow-.
Release the zip using a paper clip -4-.
Separating inner lining from hood covering
2. Release snap fastener and hook at the left and right -arrows-.
Releasing snap fastener
3. Bend the brace -1- at the left and right and remove by pulling to the front out of the tension bow -arrows-.
Removing brace
4. Remove brace -1- from the textile case on the hood inner lining -2-.
5. Open the Velcro fastener at the left and right on the tension bow -arrow-.
Opening Velcro fastener
6. Press joint out of the groove on the tension bow -arrow-.
Loosening joint on tension bow
7. Insert a plastic wedge under the metal clips -1- ( -arrow A- ) and raise them slightly -arrow B-.
Releasing metal clips
8. Carefully pull joint out of the groove on the rear window -arrows-.
Loosening joint at rear window
Removing hood inner lining at sides
1. Drill out rivets -1-.
Removing hood inner lining at sides
2. Remove hood inner lining at the sides -2- and plastic insert -3-.
Installing hood inner lining
Installing hood inner lining at sides
1. Position the hood inner lining at the sides -1- and the plastic insert -2- on the main folding top bow.
Installing hood inner lining
2. Rivet blind rivets -3- at the holes provided on the main folding top bow.
Installing hood inner lining at rear
1. Secure hood inner-lining joint to the rear window.
Securing hood inner-lining joint to rear window
1.1. Raise the metal clips using a plastic spatula -arrow A- and insert a small screwdriver under the metal clips -arrow B-.
1.2. Fit the joint seal -1- for the hood inner lining under the metal clips -arrow C-.
Check that the clearance cuts of the hood inner lining -D- are positioned at the electric connection for the rear window.
1.3. Tap in the metal clips using a plastic hammer. Make sure that the metal clips engage in the frame cut-outs.
2. Press the hood inner-lining joint into the groove on the tension bow -arrows-.
Hood inner-lining joint to tension bow
3. Fit brace -1- at the left and right into the textile case on the hood inner lining -2-. First, insert the brace into the tension bow at the rear -arrow A- , then bend it through -arrow B- and guide it forward -arrow C-.
Installing brace
Information
Only if the hood covering was replaced.
4. Pull hood covering bracing strap -3- through the cut-out in the hood inner lining and use the fastening screw -2- to secure to the corner bow -1-.
Screwing down hood covering bracing strap
5. Close the Velcro fastener at the left and right on the tension bow -arrow-.
Closing Velcro fastener
6. Press on snap fastener at the left and right -arrow-.
Pressing on snap fastener
7. Close the zip -2- between the hood inner lining at the rear -3- and the joint in the hood covering -1- in -direction of arrow-.
Lock the zip using a paper clip -4-.
Closing zip
Installing hood inner lining at front
1. Pull hood inner-lining joint -1- into the front groove on the corner bow -arrow A- and centre it.
Installing corner bow joint
2. Fit joint strip -2- into the rear groove -arrows B-.
3. Position the bracing strap -2- at the left and right under the hood inner lining -3- and secure to the main folding top bow with the fastening screw -1- ( -arrow- ).
Installing bracing strap
4. Pull bracing strap -1- at the left and right into the plastic joint on the hood inner lining -2-.
Pulling in bracing strap
5. Press Velcro fastener at the left and right of the hood inner lining onto the corner bow -arrow-.
Closing Velcro fastener
6. Position hood covering bracing strap -1- at the left and right under the tension strap bracing strap -2- and the hood inner lining bracing strap -3-. Follow the sequence shown.
Installing bracing straps
7. Screw fastening screw -4- and bracing straps to the main folding top bow -arrow-.
The wire harness for the hood -5- is also secured on the left side.
Information
Only if the hood covering was replaced.
8. Position hood inner lining bracing strap on the side -2- at the left and right above the tension strap bracing strap -1-. Follow the sequence shown.
Installing bracing straps
9. Screw fastening screw -3- and bracing straps to the main folding top bow.
The wire harness for the hood -4- is also secured on the left side.
10. Close the zip -2- between the hood inner lining at the front -1- and the joint in the hood covering -3- in -direction of arrow-.
Lock the zip using a paper clip -4-.
Closing zip
11. Secure hood inner-lining joint -2- at the left and right with fastening screws -1- ( -arrow- ).
Securing hood inner-lining joint
12. Close the Velcro fastener -1- at the left and right between the hood inner lining at the side -2- and the corner bow -3- ( -arrow- ).
Closing Velcro fastener
13. Position covering strip -2- on the roof frame (2) and press in expanding clip -1- ( -arrow- ).
Fitting hood inner-lining joint on roof frame
14. Fit sewn-on clamping rail at the back of the roof frame (1) at the left and right -arrows-.
Fitting rear clamping rail
15. Fit sewn-on clamping rail at the front of the roof frame (1) at the left and right -arrows-.
Fitting front clamping rail
16. Secure hood inner-lining joint with the fastening screws at the left and right -arrow-.
Tightening front clamping rail
Subsequent work
1. Installing hood lock -> 611919 Removing and installing hood lock - section on "Installing" Service and Repair
2. End hood service position.