6X00IN02 Disposal of airbag and seat-belt pretensioner units
WM 6X00IN Disposal of airbag and seat-belt pretensioner units
Tools
General warning notes for airbag and seat-belt pretensioner units
Disposal of airbag and belt tensioner units
Information
Country-specific statutory regulations and legislation based on them which go beyond these instructions must always be observed and take precedence over these instructions!
- Airbag units are pyrotechnical items and can pose an environmental hazard!
- For this reason, non-ignited airbag units or entire vehicles must not be disposed of as normal scrap, refuse or in other final storage facilities!
- If the vehicle suffered fire damage which caused one or several airbags or belt tensioners to be triggered, additional ignition with the adapter cable must be carried out in order to ensure that only parts without pyrotechnical contents are scrapped!
- In the case of airbag units which cannot be ignited or if the conditions for safe ignition are insufficient, always return the airbag units to Porsche or the respective importer in their original packaging!
Tools and materials
Tools for airbag units and belt tensioners
The ignition device 9257 is used for triggering the airbag units.
Ignition device 9257
The adapter cable 9257/4 is used for the driver's airbag.
Driver's airbag adapter cable 9257/4
Adapter cable of side airbag in the seat
Adapter cable of side airbag in the seat
The adapter cable 9257/3 -E- is used for the passenger's airbag, left side.
Passenger's airbag adapter cable, left side
The adapter cable 9257/5 is used for the passenger's airbag, right side.
The adapter cable 9257/3 -E- is used for the head airbag.
Head airbag adapter cable
The adapter cable 9257/6 is used for the side airbag in the seat.
Adapter cable of side airbag in the seat
The adapter cable 9257/3 -E- is used for the belt tensioner.
Belt tensioner adapter cable
Connecting ignition tool
Driver's side
Information
This is a two-stage airbag module which must be ignited separately.
- Remove trim panel for steering column. -> 481319 Removing and installing trim.
1. Disconnect plug from the airbag at the steering column switch and first insert the plug with marking A (1st stage) of adapter cable No. 9257/4.
Driver's side
2. Connect ignition device No. 9257 to the 2-pin plug E of adapter cable No. 9257/4.
3. Place the ignition device in front of the vehicle through the door gap.
4. After triggering, repeat the work step with the plug with the marking B (2nd stage).
Passenger's side
Information
Deformation of the instrument panel bracket must be expected after triggering of the passenger's airbag unit. An installed airbag unit should be intentionally triggered in installed state only if the vehicle is to be scrapped. If the instrument panel bracket is deformed in the area of the airbag mount, the instrument panel bracket will have to be replaced.
This is a two-stage airbag module which must be ignited separately.
- Remove glove compartment -> 681519 Removing and installing glove compartment
- Remove passenger's airbag unit. => Removing and installing passenger's airbag unit - Removing
1. If the instrument panel is to be re-used, remove the instrument panel. -> 701819 Removing and installing the instrument panel - Removing 701819 Removing and installing instrument panel
2. Connect the adapter cables 9257/3 (left) and 9257/5 (right) to the removed airbag unit. Re-install airbag unit with the adapter cables.
3. Connect ignition device No. 9257 to the 2-pin plug E of adapter cable No. 9257/3.
4. Place the ignition device in front of the vehicle through the door gap.
5. After triggering, repeat the work step with adapter cable No. 9257/5.
Side airbag
Information
Before disconnecting the battery, move the seat to the uppermost position.
1. Unlock and separate the electrical plug for the seat.
Side airbag
2. Connect plug of adapter cable 9257/6 to the electrical plug for the seat.
3. Connect ignition device No. 9257 to the 2-pin plug of adapter cable No. 9257/6.
4. Place the ignition device in front of the vehicle through the door gap and trigger it.
Head airbag
Remove door trim panel. => Removing and installing the door trim panel - Removing
1. Connect plug of adapter cable 9257/3 to the head airbag.
2. Connect ignition device No. 9257 to the 2-pin plug of adapter cable No. 9257/3.
3. Place the ignition device in front of the vehicle through the door gap and trigger it.
Belt tensioner
Remove the side panel lining at rear. -> 707519 Removing and installing rear side panel lining 707519 Removing and installing rear side trim panel
1. Connect plug of adapter cable 9257/3 to the belt tensioner.
2. Connect ignition device No. 9257 to the 2-pin plug of adapter cable No. 9257/3.
3. Place the ignition device in front of the vehicle through the door gap and trigger it.
Triggering of airbag units
WARNING
Detonation of airbag units.
- Danger of injury from emerging objects, e.g. splinters.
- Hearing impairment by explosion noises.
- Danger of burns from hot airbag units.
- Danger of poisoning by emerging gases.
-> Observe a safety distance of at least 10 m.
-> Wear hearing protection.
-> Each airbag unit, the respective ignition stages 1 and 2, and each belt tensioner must be triggered individually.
-> Allow airbag units to cool down for the appropriate time.
-> Open the vehicle doors to allow the gases to escape.
Connect the ignition device to a separate battery and press the button.
Triggering of airbag units