97095505 Replacing sub-part for rear left wheel housing (TPM)
WM 970955 Replacing sub-part for rear left wheel housing (TPM)
Tools
Information
The main wire harness is manufactured individually depending on equipment.
- Fastening elements may be different from the parts described.
- The number of plug connections can vary, depending on equipment.
Installation position of sub-part for rear left wheel housing (TPM)
Preliminary work
1. Disconnect the battery. -> 2X00IN Work instructions after disconnecting the battery - section on "Disconnecting" 2X00IN Work instructions after disconnecting the battery
2. Remove carpet at the left. -> 704119 Removing and installing carpet - section on "Removing"
3. Remove side cushion at the left. -> 724919 Removing and installing side cushion - section on "Removing" 724919 Removing and installing side cushion
4. Remove C-pillar trim panel with sound absorber on driver's side. -> 706819 Removing and installing C-pillar trim panel - section on "Removing" 706819 Removing and installing C-pillar trim
5. Remove left rear wheel. -> 440519 Removing and installing wheel - section on "removing" Removal and Replacement
6. Remove left rear wheel housing liner. -> 536919 Removing and installing rear wheel housing liner - section on "Removing" Service and Repair
Removing sub-part for rear left wheel housing (TPM)
1. Remove cable cover on rear inner sill.
Removing cable cover on rear inner sill
1.1. Unscrew fastening screws -1- on cable cover.
1.2. Remove cable cover
2. Unclip main wire harness.
Information
When cutting the front wire harness, make sure there is enough length of cable left to join to the new lines.
3. Disconnect part of the wire harness for the rear left wheel housing from the main wire harness and cut it off in area -x-.
Connection part of sub-part for rear left wheel housing (TPM)
4. Make sure that all fastenings on the rear left wire harness in the interior are disconnected.
5. Loosen rubber sleeve in the rear left wheel housing, remove it by pushing it towards the wheel housing and carefully remove the wire harness from the interior by pushing it towards the wheel housing.
6. Loosen sub-part of wire harness in the rear left wheel housing at all five fastening points -x- and release and pull off all plug connections.
Fastening points for sub-part for rear left wheel housing (TPM)
7. Make sure that all fastenings on the wire harness for the rear left wheel housing are disconnected.
8. Remove entire sub-part of wire harness for rear left wheel housing.
Installing sub-part of wire harness for rear left wheel housing (TPM)
1. Push wire harness for rear left wheel housing (TPM) through towards the interior and fit rubber sleeve.
2. Fit sub-part of wire harness in the rear left wheel housing at all five fastening points -A- and plug in and lock all plug connections.
Fastening points for sub-part for rear left wheel housing (TPM)
Information
Select a place for the joint where there is enough space to join all the lines present.
Do not cut the lines too short in case they have to be laid in a different position if there is insufficient space in the area of the joint.
Information
The greatest care must be used in the individual work steps for stripping insulation from, crimping, and shrinking/insulating the electric lines.
The procedure for stripping insulation from, crimping, and shrinking/insulating the electric lines must be complied with and observed. The procedures are described in detail in the Repair kit for Cayenne wire harnesses NR.155-2.
Crimping samples are to be prepared before beginning work.
Information
Allocation of lines - see wiring diagram.
3. Crimp the lines in area -x-.
Connection part of sub-part for rear left wheel housing (TPM)
3.1. Cut off lines in different lengths (due to the shrink-fit connections).
3.2. Slide shrink-fit hoses onto the lines.
3.3. Strip 10 mm of insulation off the wires.
3.4. Crimp lines using crimping sleeves and the hand crimping pliers from the repair kit for wire harnesses Nr.155-1.
3.5. Slide the shrink-fit hoses over the crimp connections and carefully shrink them using the hot-air blower with special nozzle (recommended accessories for the repair kit for wire harnesses) so that they are watertight.
3.6. Wrap commercially available PVC tape all around the area of the connection points.
3.7. Secure the repaired area -x- to the main wire harness with tie-wraps.
4. Installation is performed in reverse order.
5. Secure the cable duct to the rear left inner sill.
Subsequent work
1. Install rear left wheel housing liner. -> 536919 Removing and installing rear wheel housing liner - section on "Installing" Service and Repair
2. Install rear left wheel. -> 440519 Removing and installing wheel - section on "Installing" Removal and Replacement
3. Install C-pillar trim panel with sound absorber on driver's side. -> 706819 Removing and installing C-pillar trim panel - section on "Installing" 706819 Removing and installing C-pillar trim
4. Install side cushion at the left. -> 724919 Removing and installing side cushion - section on "Installing" 724919 Removing and installing side cushion
5. Fit carpet at the left. -> 704119 Removing and installing carpet - section on "Installing"
6. Connect the battery. -> 2X00IN Work instructions after disconnecting the battery - section on "Connecting" 2X00IN Work instructions after disconnecting the battery