Part 2

Thread Repair (Part 2)

Tapered Pipe Thread Repair

The thread repair insert for tapered pipe threads is coated with a clear silver zinc coating.





Refer to Safety Glasses Warning.

Note
The use of a cutting type fluid, WD 40(R) or equivalent is recommended when performing the drilling, counterboring and tapping procedures. Refer to Adhesives, Fluids, Lubricants, and Sealers for recommended cutting fluid.

When installed to the proper depth, the flange (1) of the insert will be seated against surface (2) of the base material of the drilled/tapped hole.

1. Note
- During the drilling process, it is necessary to repeatedly remove the drill and clean chips from the hole and the flutes of the drill.
- Drill the hole until the stop collar contacts the surface of the base material.

Drill out the threads of the damaged hole.





2. Note
All chips must be removed from the drilled hole prior to tapping.

Using compressed air, clean out any chips.





3. Note
- During the tapping process, it is necessary to repeatedly remove the tap and clean chips from the hole and the flutes of the tap.
- Ensure the tap has created full threads at least to the depth equal to the insert length.

Using a suitable tapping wrench, tap the threads of the drilled hole by hand only.





4. Tap the drilled hole until the threads at the top of the tap (2) are down to the surface of the base material.





5. Note
All chips must be removed from the tapped hole prior to insert installation.

Using compressed air, clean out any chips.





6. Spray cleaner into the tapped hole. Refer to Adhesives, Fluids, Lubricants, and Sealers for recommended cleaner.





7. Note
All chips must be removed from the tapped hole prior to insert installation.

Using compressed air, clean out any chips.





8. Note
Do not allow oil or other foreign material to contact the outside diameter (OD) of the insert.

Lubricate the threads of the driver installation tool (2) with the EN 42385-110 (1).





9. Install the insert (2) onto the driver installation tool (1).





10. Apply threadlock sealant, EN 42385-109, LOCTITE 277(R) or equivalent (1) to the insert OD threads (2). Refer to Adhesives, Fluids, Lubricants, and Sealers for recommended sealant.





11. Install the insert (2) into the tapped hole by hand only.





12. Note
If the insert will not thread down until the flange contacts the surface of the base material remove the insert immediately with a screw extracting tool and inspect the tapped hole for any remaining chips and/or improper tapping.

Install the insert until the flange of the insert (3) contacts the surface of the base material.





13. Note
The driver installation tool will tighten up before screwing completely through the insert. This is acceptable. The threads at the bottom of the insert are being formed and the insert is mechanically locking the insert into the base material threads.

Continue to rotate the driver installation tool (1) until the top of the threaded section (2) is level with the top of the insert (3).
14. Inspect the insert (1) for proper installation (2) into the tapped hole.





15. Any installed insert that restricts or blocks an oil or engine coolant passage (3) will need to have the oil or engine coolant passage drilled out (4) to the original size of the oil or engine coolant passage. After drilling the restriction or blockage, clean out any chips and thread the installation driver tool through the insert again to remove any burrs caused by the drilling of the oil or engine coolant passage.





Cylinder Head Bolt Hole Thread Repair

Special Tools

- EN 42385-700 High Feature Thread Repair Kit
- EN 42385-2000 Thread Insert Kit

For equivalent regional tools, refer to Special Tools.





Tools for repairing threaded bolt holes in the cylinder head are included in the insert kit EN 42385-2000 and the kit EN 42385-700. Components for repairing threaded bolt holes in the cylinder head consist of:

- EN 42385-723 Drill (1)
- EN 42385-724 Tap (2)
- EN 42385-725 Installation driver (3)
- EN 42385-303 Alignment pin (4)
- EN 42385-302 Bushing (5)
- EN 42385-733 Bolts (6)
- EN 42385-401 Fixture plate (7)

Refer to Safety Glasses Warning.

Note
- Remove the fixture plate prior to installing the insert with the installer tool.
- The use of a cutting type fluid, WD 40(R); or equivalent is recommended when performing the drilling, counterboring and tapping procedures. Refer to Adhesives, Fluids, Lubricants, and Sealers for recommended cutting fluid.

When installed to the proper depth, the flange of the insert will be seated against the counterbore of the drilled/tapped hole.

1. Position the fixture plate (3) with the bushing (1) installed over the cylinder head bolt hole to be repaired (4).





2. Loosely install the fixture plate bolts (2) into the remaining cylinder head bolt holes.
3. Position the alignment pin (1) through the bushing and into the cylinder head bolt hole.





4. With the alignment pin in the desired cylinder head bolt hole, tighten the fixture retaining bolts (2).
5. Remove the alignment pin (1) from the cylinder head bolt hole.

6. Note
- During the drilling process, it is necessary to repeatedly remove the drill and clean chips from the hole and the flutes of the drill.
- Drill the hole until the stop collar contacts the top of the drill bushing.

Drill out the threads of the damaged hole.





7. Note
All chips must be removed from the drilled hole prior to tapping.

Using compressed air, clean out any chips.





8. Note
- During the tapping process, it is necessary to repeatedly remove the tap and clean chips from the hole and the flutes of the tap.
- Ensure the tap has created full threads at least to the depth equal to the insert length.

Using a suitable tapping wrench, tap the threads of the drilled hole by hand only.





9. In order to tap the new threads for the insert to the proper depth, rotate the tap into the cylinder head bolt hole until the mark (3) on the tap aligns with the top of the drill bushing (2).





10. Note
Remove the fixture plate prior to installing the insert with the installer tool.

Remove the fixture plate bolts (2).





11. Remove the fixture plate (3) and bushing (1).

12. Note
All chips must be removed from the tapped hole prior to insert installation.

Using compressed air, clean out any chips.





13. Spray cleaner into the tapped hole. Refer to Adhesives, Fluids, Lubricants, and Sealers for recommended cleaner.





14. Note
All chips must be removed from the tapped hole prior to insert installation.

Using compressed air, clean out any chips.





15. Note
Do not allow oil or other foreign material to contact the outside diameter (OD) of the insert.

Lubricate the threads of the driver installation tool (2) with the EN 42385-110 (1).





16. Install the insert (2) onto the driver installation tool (1).





17. Apply threadlock sealant, EN 42385-109, LOCTITE 277(R); or equivalent (1) to the insert OD threads (2). Refer to Adhesives, Fluids, Lubricants, and Sealers for recommended sealant.





18. Install the insert and installation driver (1) into the tapped hole by hand only.





19. Start the insert into the threaded hole.

20. Note
If the insert will not thread down until the flange contacts the counterbored surface remove the insert immediately with a screw extracting tool and inspect the tapped hole for any remaining chips and/or improper tapping.

21. Note
The driver installation tool will tighten up before screwing completely through the insert. This is acceptable. The threads at the bottom of the insert are being formed and the insert is mechanically locking the insert into the base material threads.

Continue to rotate the driver installation tool through the insert.
22. In order to completely form the new threads in the insert, rotate the driver installation tool through the insert until the mark (1) on the driver installation tool aligns with the surface of the engine block deck (2).





23. Inspect the insert for proper installation into the tapped hole.