Suspension - Creaking From Rear of Vehicle
BULLETIN NO.: 02-T-14AISSUE DATE: May, 2002
CATEGORY TYPE: Chassis-05
CATEGORY: Rear Suspension
CORPORATION NO.: 02-03-09-001A
SUBJECT:
Creaking Noise from Rear of Vehicle While Driving
(Replace and Secure all Four Insulators to Rear Coil Springs)
Due to a change in coil spring orientation and a new coil spring insulator P/N 22705168, this bulletin has been revised and supersedes bulletin 02-T-14 which should be discarded.
MODELS AFFECTED:
2002 Saturn VUE vehicles up to and including VIN 2S825308
CONDITION:
Some customers may comment about a creaking noise coming from the right or left rear of the vehicle while driving.
CAUSE:
This condition may be caused by a dislodged coil spring insulator from a seated position during installation, allowing metallic contact of the coil spring to seat.
CORRECTION:
To correct this condition, replace upper and lower coil spring insulators (both sides of vehicle) with new coil spring insulator P/N 22705168. Secure insulators to coil springs and reinstall springs ensuring that part number identification tape located on the coil spring is oriented inboard of the vehicle and at the top of the spring. Refer to service procedure in this bulletin.
SERVICE PROCEDURE
Removal
CAUTION:
MAKE SURE VEHICLE IS PROPERLY SUPPORTED AND SQUARELY POSITIONED ON THE HOIST. TO HELP AVOID PERSONAL INJURY WHEN A VEHICLE IS ON THE HOIST, PROVIDE ADDITIONAL SUPPORT FOR THE VEHICLE OPPOSITE FROM WHICH COMPONENTS ARE BEING REMOVED.
1. Raise vehicle.
2. Remove wheel and tire.
IMPORTANT:
Hold stabilizer link with wrench to avoid damage to stabilizer link.
3. Remove stabilizer link to lower control arm nut.
4. Securely position a screw type jack stand under lower control arm. Using the jack stand, apply a small force to assist with bolt removal.
5. Remove lower shock absorber bolt.
6. Remove lower control arm knuckle bolt.
CAUTION:
LOWER JACK STAND SLOWLY TO AVOID PERSONAL INJURY.
7. Using jack stand slowly unload coil spring.
8. Remove coil spring and spring insulators.
Installation
NOTICE:
Inspect coil spring for abrasion. If the black protective coating on coil spring is worn through replace the spring.
1. Fully seat new top and bottom coil spring insulators to the spring.
IMPORTANT:
There are six slots molded into the insulator. When securing the insulator, use slot as in illustration (second slot in the clockwise direction closest to the end of the coil spring) and position a tie strap at that location around insulator and spring. Snug the tie strap by hand and cut off any excess. Install second strap 180° from the first.
2. Using 1/8 x 6 in. plastic tie straps, secure insulator to coil spring using two straps on top and two straps on the bottom for each spring.
IMPORTANT:
Ensure that part number identification tape located on the coil spring is oriented inboard of the vehicle and at the top of the spring.
IMPORTANT:
Silicon spray lubricant can be used on the insulator to lower control arm contact area to assist with installation.
3. Install coil spring with insulators onto lower control arm.
NOTICE:
Ensure coil spring is properly seated.
4. Reposition screw type jack stand under lower control arm and slowly raise control arm towards knuckle While aligning upper coil spring onto its seat, ensure the ID tape is oriented inboard of the vehicle and at the top of the spring.
IMPORTANT:
Bolt head must face towards rear of vehicle.
5. Align lower control arm to knuckle, insert bolt, install new nut and tighten.
Torque:
Lower Control Arm to Knuckle
Bolt: 110 N.m (81 ft-lbs)
NOTICE:
Tie straps must be removed to ensure noise does not persist.
6. Cut and remove all tie straps from upper and lower coil spring locations.
7. Align shock absorber to lower control arm mount, insert bolt and tighten.
Torque:
Shock to Lower Control Arm
Bolt: 110 N.m (81 ft-lbs)
8. Install jounce bumper nut and tighten.
Torque:
Jounce Bumper Nut: 63 N.m (46 ft-lbs)
NOTICE:
Hold stabilizer link with wrench to avoid damage to the link.
9. Position stabilizer link to lower control arm, install nut and tighten.
Torque:
Stabilizer Link to Lower Control
Arm: 15 N.m (11 ft-lbs)
10. Position wheel and tire onto hub install wheel nuts and tighten in a criss-cross pattern.
Torque:
Wheel Nuts: 125 N.m (92 ft-lbs)
11. Repeat procedure for other side of vehicle.
12. Lower vehicle from hoist.
PARTS REQUIREMENTS:
CLAIM INFORMATION:
To receive credit for this repair during the warranty coverage period, submit a claim through the Saturn Dealer System for F5027 (Spring, Rear Coil. Both - R&R or Replace), refer to the appropriate Electronic Labor Time Guide for the correct Labor Operation Code and Time.
Disclaimer