Procedure

1. Verify customer comment by performing HVAC Performance Test in the HVAC section of the 2002-2003 Saturn VUE Service Manual. If system performance indicates a low refrigerant charge, go to the next step. If performance test does not indicate a low system charge, review Diagnostic Charts in the HVAC section of the 2002-2003 Saturn VUE Service Manual to repair/eliminate condition associated with customer's comment.

2. Raise vehicle on hoist.





3. Using service tool Black Light J42220 with specially tinted goggles, inspect PRV for leakage. (PRV is located on the A/C hose manifold on the side of the AC compressor.) The PRV has a paper seal installed on the bottom over the opening. If the PRV has vented, one of the following conditions will be observed:

^ The seal will glow

^ The seal will be torn

^ The seal will be missing





If the seal meets any of the above conditions, lower vehicle and go to the Suction/Discharge Hose Removal procedure.

If the seal is intact and does not glow with the black light, inspect other components for leaks.

Suction/Discharge Hose

Removal:

Important:
Verifying the purity of the refrigerant with a refrigerant identifier is recommended before recovery.

1. Recover refrigerant using an approved refrigerant recovery system. Measure the amount of oil lost during recovery and record.





2. Remove left headlamp. (Refer to "Headlamp Assembly" removal procedure in the "Front End" section of the 2002-2003 Saturn VUE Body Removal & Installation Service Manual.)





3. Unclip suction hose from battery box clip.





4. On L81 vehicles, remove suction hose to suction hose jumper joint nut and line.





5. Install protective cap to suction hose to prevent contamination and desiccant saturation.

6. On L61 vehicles, remove nut from TXV on suction hose side and remove suction hose.

7. Remove nut from discharge line stud on condenser and remove discharge line.

8. Install protective cap to condenser to prevent contamination and desiccant saturation.

9. Raise vehicle on hoist.





10. Disconnect pressure transducer electrical connector.

11. With open end wrench, remove pressure transducer. Pressure transducer will need to be installed on new suction/discharge hose.

12. Drain oil from discharge line and measure the amount of oil removed from the system.

Note:
The quantity of oil lost must be added to system or damage to the compressor may occur.





13. Install protective cap to compressor to prevent contamination.

Installation

1. Remove protective cap from compressor end of suction/discharge hose assembly and compressor. Install new seal washers and install hose manifold block to compressor.





Important:
Do not lubricate seal washers. By design, seal washer lubricant is not required. If a lubricant is used during installation, the oil used to lubricate the seal may be mis-diagnosed as a seal/joint leak.

Remove protective cap from compressor end of suction/discharge hose assembly and compressor. Install new seal washers and install hose manifold block to compressor.

Tighten

Tighten the Hose Assembly to Compressor to 27 N.m 20 (ft-lbs).

Note:
Use R-12 refrigerant oil (mineral) to lubricate 0-rings. Use of R-134a (PAG) oil will cause premature corrosion of fitting joints.

Note:
Use only clean lint free cloths with non-petroleum based solvents to clean refrigerant system sealing surfaces. Allow solvent to dry with air. Do not allow solvent to enter refrigerant system. If a lint free cloth is not used, particles are left behind and will interfere with the seal.

2. Lubricate new pressure port 0-ring with mineral oil.

3. Hand start pressure transducer onto pressure port taking care not to pinch 0-ring and tighten.

Tighten

Tighten the Pressure Transducer to 10 N.m 89 (in-lbs).

4. Connect electrical connector to pressure transducer.





5. On L81 vehicles, remove caps from suction hose and suction jumper and install new seal washer then hose.

Tighten

Tighten the Seal Washer-Suction Hose to 16 N.m (12 ft-lbs).





6. Lubricate pressure relief valve 0-ring with new R-12 mineral oil. Install valve and torque to specification.

Note:
Use R-12 refrigerant oil (mineral oil) to lubricate 0-rings. Use of R-134A (PAG) oil will cause premature corrosion of fitting joints.

Tighten

Tighten the Pressure Relief Valve to 10 N.m (89 in-lbs).

7. Lower vehicle.





8. On L61 vehicles, remove cap from TXV at TXV end of suction hose assembly. Install new hose with seal washer.

Tighten

Tighten the Nut-Suction Hose at TXV to 16 N.m (12 ft-lbs).





9. Remove protective cap at condenser end of discharge hose assembly. Connect new hose with seal washer.

Tighten

Tighten the Nut-Discharge Hose at Condenser to 16 N.m (12 ft-lbs).





10. Clip suction hose to battery box.





11. Install left headlamp. (Refer to "Headlamp Assembly" installation procedure in the "Front End" section of the 2002-2003 Saturn VUE Body Removal & Installation Service Manual.)

12. Evacuate, charge, and leak check the A/C system. Repair any leaks as required. If no leaks are found, return the vehicle to customer.