Operation CHARM: Car repair manuals for everyone.

B0188




DTC B0183 or B0188

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (Initial Inspection and Diagnostic Overview) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Initial Inspection and Diagnostic Overview) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Initial Inspection and Diagnostic Overview) provides an overview of each diagnostic category.

DTC Descriptors
DTC B0183 02
- Solar Load Sensor 1 Circuit Short to Ground

DTC B0183 05
- Solar Load Sensor 1 Circuit Short to Short to Battery or Open

DTC B0188 02
- Solar Load Sensor 2 Circuit Short to Ground

DTC B0188 05
- Solar Load Sensor 2 Circuit Short to Short to Battery or Open

Diagnostic Fault Information





Circuit Description

The sunload sensor is a 2-wire photo diode. The vehicle uses left and right sunload sensors. The two sensors are integrated into the sunload sensor assembly along with the ambient light sensor. Body ground and signal circuits enable the sensor to operate. As the sunload increases, the sensor signal decreases. The sensor operates within an intensity range between completely dark and very bright. The sensor signal varies between 0 and 5 volts. The HVAC control module converts the signal to a range between 0 and 255 counts. The sunload sensor provides the HVAC control module with a measurement of the amount of light shining on the vehicle. Bright or high intensity light causes the vehicles interior temperature to increase. The HVAC system compensates for the increased temperature by diverting additional cool air into the vehicle.

The following DTCs are for the left and right sunload sensors.

* B0183 is for the left sunload sensor.
* B0188 is for the right sunload sensor.

Conditions for Running the DTC

Ignition ON.

Conditions for Setting the DTC

The HVAC control module detects the signal circuit is less than 5 counts or more than 250 counts.

Action Taken When the DTC Sets

If the DTC is set the system will act as if no sunload condition exists.

Conditions for Clearing the DTC

* The DTC will become history if the HVAC control module no longer detects the condition that set the DTC.
* The history DTC will clear after 100 fault-free ignition cycles.

Reference Information
Schematic Reference

HVAC Schematics (HVAC - Automatic)
Connector End View Reference

Component Connector End Views (Connector Views)
Description and Operation

* Air Temperature Description and Operation (Air Temperature Description and Operation)
* Air Delivery Description and Operation (Air Delivery Description and Operation)

Electrical Information Reference

* Circuit Testing (Component Tests and General Diagnostics)
* Connector Repairs (Component Tests and General Diagnostics)
* Testing for Intermittent Conditions and Poor Connections (Component Tests and General Diagnostics)
* Wiring Repairs (Component Tests and General Diagnostics)

Scan Tool Reference

Control Module References (Programming and Relearning) for scan tool information

Circuit/System Verification

Ignition ON, observe the appropriate scan tool Sunload Sensor parameter. The reading should be between 5 and 250 counts and change with sunlight changes.

Circuit/System Testing

Important: If a solar load sensor has an out of range condition caused by a short to voltage, short to ground, or an open/high resistance, the scan tool will display the same value: 225 counts.

1. Ignition OFF, disconnect the harness connector at the sunload sensor.
2. Test for less than 10 ohms between the ground circuit terminal C and ground.

If greater than the specified range, test the ground circuit for an open/high resistance.

3. Ignition ON, test for 4.8-5.2 volts between the appropriate signal circuit terminal listed below and ground:

* Left solar load sensor circuit terminal A
* Right solar load sensor circuit terminal B

If less than the specified range, test the signal circuit for a short to ground or open/high resistance. If the circuit tests normal, replace the HVAC control module.
If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the HVAC control module.

4. If all circuits test normal, test or replace the sunload sensor.

Repair Instructions

Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.

* Headlamp Automatic Control Ambient Light Sensor Replacement (Service and Repair)
* Control Module References (Programming and Relearning) for HVAC control module replacement, setup, and programming